Search models, users, collections, and posts

First Aid Kit Rugged Box

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
H2D
H2D Pro
H2S
P2S
H2C
X2D
A2L

PETG - 0.2mm layer, 4 walls, 12% infill
PETG - 0.2mm layer, 4 walls, 12% infill
Designer
12.1 h
4 plates
5.0(22)

Open in Bambu Studio
Boost
218
570
24
24
556
155
Released 

Description

Membership

Commercial Sales subscriptions 💰 now available. A single Battery Caddy sale covers your entire month!

Join

Boost Me (for free)

If you like this model, please consider boosting me. It's free! Thank you! 💙💙🙏

First Aid Kit Rugged Box

First Aid Kit rugged box for storing quick access to first aid essentials. Internal dimensions are 150mm x 150mm x 50mm - about 6" x 6" x 2" to hold plenty of useful supplies and still not take up a lot of room.

 

Great for the home, work, car, workshop, camping, and anywhere a compact first aid kit could be useful, yet large enough to hold useful items during a first aid emergency.

 

The rugged box is of my own design, not a remix of any others. To assemble, you will need 4, 3mm x 50mm pins. I use these: https://a.co/d/06UJCJyv . These press-fit into the hinges and latches. The hinge and latch side portions use a friction fit to hold the pin in place, while the rotating portion of the hinge and latch are slightly larger and rotate freely. Be sure and print the “gasket” in TPU, it slips into the “lid” portion and provides a water-resistant seal, and also provides a bit of “squish” for the latches to engage properly.

Parts Needed

  1. 4 pins (I use these) - https://a.co/d/06UJCJyv
  2. First Aid Kit Refill Supplies (see below for suggestions)

Pack it with the essentials that are suitable for your needs. There are many first-aid kit refill packs available. I used items from this pack, but there are many others that may suit your needs better. I also put in some blood-clotting treatment because my father is on blood thinners and even a small cut can be dangerous. In additional to those, I put in some insect sting treatment for the kids (and adults, too!). So I combined items from these three first-aid refill and supplies. These are my personal choices, and may change over time. You can fill it with what is important for you, of course. :-)

  1. First Aid Refill - bandages, burn dressing, sterile wipes, tape, scissors, etc: https://a.co/d/0aJeMA7Z
  2. First Aid Powder for Blood Clotting Trauma Kit - for stopping moderate to severe bleeding: https://a.co/d/08HUziNH
  3. Insect Sting Relief Pads - temporary pain relief for insect bites, minor burns, and scrapes: https://a.co/d/0e6FUgvH

Whether you use this model or not, I do recommend having a first aid kit nearby in places you frequent, as you never know when an accident may occur. And having the essentials quickly available on-hand could save valuable time in treating you or your patient, and possibly even save a life!

 

Boost Me (for free)

If you like this model, please consider boosting me. It's free! Thank you! 💙💙🙏

Membership

Commercial Sales subscriptions 💰 now available. A single Battery Caddy sale covers your entire month!

Join

Comment & Rating (24)

(0/1000)

Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
I used m3x50 bolts rather than the pins - seems ok.
1
Reply
Boosted
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
Printed as expected. Nice design, thank you!
(Edited)
0
Reply
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
easy to print. I made a bit smaller
0
Reply
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
Cool strong print! printed hinges that work well.
0
Reply
Boosted
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
fantastic print, works really well. thank you
0
Reply
I currently don't have tpu or the ability to print tpu. Is that make or break for the gasket?
The designer has replied
0
Reply
Printing without the gasket is fine. I think the lid works a little better with the gasket, but it’s totally fine without it also.
0
Reply
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
sturdy box and printed super easy
0
Reply
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
0
Reply
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
(Edited)
0
Reply
Print Profile
PETG - 0.2mm layer, 4 walls, 12% infill
0
Reply

License

If you want to use this model commercially, please join my membership.
Join Now
This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.