Search models, users, collections, and posts

s23 ultra tpu cover (V2.0 now available)

flo89
Hobby & DIY>Electronics
IP Report

Print Profile(2)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini
H2D
H2D Pro
H2S
P2S
H2C
X2D
A2L
v2.0
v2.0
Designer
1.3 h
1 plate
4.5(65)
0.2mm layer, 2 walls, 30% infill
0.2mm layer, 2 walls, 30% infill
Designer
1.2 h
1 plate
4.6(22)
Open in Bambu Studio
Boost
225
473
111
38
1.2 k
695
Released 

Description

TPU cover for Samsung s23 ultra

 

s23 ultra
phone case
phone
phone accessiories
phone accessories
phone accessory
Samsung
samsung 860

Comment & Rating (111)

(0/1000)
@dhdeskisiado
Boosted
the case printed very good as well as the supports being super easy to remove. no need to cut them. only 2 gripes with it. I wish the case had buttons, too hard to press as it is, and the bottom needs to be thinner and the whole for the stylus enlarged. I may try to do those modifications and upload the result.
designer
6
Reply
@Svenkasulke
Boosted
I must say you did that very well I didn't slice it, I just started it from my phone and I have to say it looks really good So I don't have any problems with the buttons What I've noticed now is that it wasn't great only around the stylus But no problem, just get a utility knife and carefully trim it
The designer has replied
Show original
designer
1
Reply
@flo89
thnx
0
Reply
@Svenkasulke
Boosted
Replying to @flo89 :
A little tip by the way, steal the on/off and volume up/down buttons from another profile. I stole some from Pixel and now the buttons are much easier to press
Show original
1
Reply
@flo89
Replying to @Svenkasulke :
I just uploaded a version 2.0. I'm open for feedback.
1
Reply
@ProfBryant
Boosted
This is a pretty nice case. It was my first print using TPU, and I am pretty happy with the results. If you make a version 2, the minor issues that I observed are that it it hard to press the power and volume buttons, and the S pen is hard to remove due to the thickness of the base. Thanks for your contribution! Keep up the good work.
(Edited)
The designer has replied
1
Reply
@flo89
thnx for the feedback. print looks really nice in red😃
0
Reply
@flo89
@ProfBryant I just uploaded a version 2.0. I'm open for feedback.
(Edited)
0
Reply
@krzzich
Print Profile
0.2mm layer, 2 walls, 30% infill
Good design, but it could be thinner around button holes and S-Pen
The profile uploader has replied
0
Reply
@flo89
what version thit you print? it looks like v1. in v2 i fixt this.
0
Reply
@krzzich
Oh, didn't saw the V2.. Will try soon 👍👍
0
Reply
@Dylan_Hansen
Print Profile
0.2mm layer, 2 walls, 30% infill
would have required some support where the button goes to but other than I’m really happy with it 👍🏻
The profile uploader has replied
0
Reply
@flo89
thanx for the rating. with lots of cooling mine got a little bit better but not perfect either. support with tpu is hard because it fuses with the printed part. If somebody has some suggestions that be great.
(Edited)
0
Reply
@flo89
@Dylan_Hansen I just uploaded a version 2.0. I'm open for feedback.
0
Reply
@Dmastronardi
Print Profile
v2.0
My inaugural print utilizing generic TPU, conducted at 205 degrees, proved exceptionally successful
Show original
1
Reply
@nozzles
Print Profile
v2.0
tpu is not easy to print, thank you
1
Reply
@jkr115
Print Profile
v2.0
good model, probably just gotta tweak my filament settings
The profile uploader has replied
0
Reply
@flo89
looks like theire is some moisture in your filiment. print looks nice.
0
Reply
@Svenkasulke
Boosted
Print Profile
0.2mm layer, 2 walls, 30% infill
Simply perfect
Show original
profile
1
Reply
@user_1479406286
did I do something wrong? its my first time with tpu
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

The Perfect TPU profile
The Perfect TPU profile
AllFor3D
23.6 k
5.3 k
Rise of the Dragon * Now With Magnets
Rise of the Dragon * Now With Magnets
Steve
34.4 k
7 k
Iphone 17 pro
Iphone 17 pro
Cereales
16.6 k
3.6 k
Airless Soccer Ball
Airless Soccer Ball
OVERTURE Filament
17.5 k
3.9 k