Printable Hand Vise - Free 3D Print Model

Search models, users, collections, and posts

blecheimer

Tools>Hand Tools

IP Report

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

A1 mini

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

Designer

1.9 h

1 plate

4.8(31)

ABS - 0.6mm nozzle, 0.3mm layer, 4 walls, 10% infill

2.2 h

1 plate

5.0(4)

0.16mm layer, 4 walls, 15% infill ABS Handle only

1 h

1 plate

Open in Bambu Studio

Boost

220

639

394

245

Released

Description

When working with small models sometimes my fingers just are too big. So I made a fully printable hand vise.

To clamp something you simply turn the handle.

Print everything with a layer height of 0.2mm or lower. Support is not needed. The thread is close to M12 and should work directly after printing. You can lubricate the thread with candle wax so it runs smoother.
For the hinges I designed hinge rivets. Install the claws to the claw-bridge then insert the rivets. Heat up a flat piece of metal (e.g. a flat screwdriver) and press it on the small end of the rivet. The rivet will melt in place.

Disclaimer:
This work by blecheimer is licensed under CC BY-NC-SA 4.0
You are not allowed to copy this model to other 3D printing websites without my permission.

vice

handvice

clamp

Comment & Rating (47)

@user_1334538231

Print Profile

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

Using Bambu labs white HF PETG.

@SoViN

Print Profile

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

Excellent

Show original

@brentk

Boosted

The handle failed mid-print twice, but the last time it was almost complete. I was able to just reprint the rounded tip of it and sand it and glue it on. It also has some lumpy quality issues. I'm assuming both of these issues stem from printing in on a bed slinger (A1 Mini) where tall, thin prints can be problematic with them being jerked around. Other than that, works great!

@Zpazer

Print Profile

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

Nice little hand Vise. I hope the jaw would open more than 10mm For small detail projects is perfect

@Xaverl

Print Profile

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

funktioniert

@hectorri

Nice tool! Thank you.

(Edited)

@Schidter

Print Profile

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

Great design. Works and prints great. Seems to be pretty strong with ABS. Had some ideas for further development. perhaps some hooks for rubber bands so that the teeth don’t have to be manually separated other grip sizes would be cool as well. all in all, great print

@user_2559345840

i was wondering if there are any jaws with a more "forward" angle? even when empty, there's a gap at the front for me. it only gets bigger the bigger the object is.

@Carlos_Gwn

Boosted

Print Profile

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

@WizEv1

Print Profile

Standard PLA, AMS supported - 0.2mm layer, 3 walls, 10% infill

dosent work that well and really small opening

The profile uploader has replied

@blecheimer

Are you rating the print profile or the model? Likes are for the model, ratings for the profile. Are there any issues with the print profile?

@WizEv1

I am rating the model the print profile is really good

@blecheimer

Replying to @WizEv1 :

If the print profile is really good, why do you rate the profile only three stars? Remember - the rating is only for the print profile. So other users know if this profile works. If you do not like the model (which is totally ok), just write it in the comments.