SlideGuide- Cable and Hose Guard for Car Detailing - Free 3D Print Model

Search models, users, collections, and posts

Optivex

Tools>Hand Tools

IP Report

Print Profile(2)

All

P2S

H2D

H2D Pro

H2C

P1P

H2S

X2D

P1S

A1 mini

X1 Carbon

X1E

A2L

0.4mm nozzle - 0.2mm layer, 5% gyroid, 4 walls

Designer

2 h

1 plate

4.8(33)

0.6mm nozzle - 0.3mm layer, 5% gyroid, 4 walls

Designer

1.4 h

1 plate

5.0(4)

Open in Bambu Studio

Boost

747

2599

695

501

Released

Bill of Materials

Bambu Filaments

Select all

Lime Green (33501) / Filament with spool / 1 kg

Description

Boost Me (for free)

If you like my work, please consider boosting!

Tyred (heh) of your cables and hoses snagging between the tyres and ground when detailing your car?
Pressure washer or regular water hoses, power cables from polishing machines or vacuum cleaner - we've all been there!

I've seen some solutions for this around, but they are either unoptimized for printing or take too long to print, so I thought I'd give it my own take.

This single piece, ~2 hour print is designed to do just that. It can be used on any tyre - front, back, left, right.

Simply print however many as you need, and wedge them in.

Comment & Rating (57)

@TheLayerLayer

Print Profile

0.4mm nozzle - 0.2mm layer, 5% gyroid, 4 walls

came out great I used sunlu PETG in bright green so I dont forget theyre behind the tires

The profile uploader has replied

@optivex

Awesome!

@Chvfrk98

Boosted

Print Profile

0.4mm nozzle - 0.2mm layer, 5% gyroid, 4 walls

I scaled up a bit. I’ll be giving these to a couple of friends most definately. thanks for model

@k4hvf

Boosted

Print Profile

0.4mm nozzle - 0.2mm layer, 5% gyroid, 4 walls

Great easy print with ABS. Printed two and both came out with the same pattern on them for some reason but they work well. Not sure why they have them.

(Edited)

@Streiti

Boosted

Hello, I printed these two in PETG, and they are great! However, I do have a request: would it be possible to make them taper to a sharper point? That would allow me to wedge them under the tires more effectively, and they would hold better with smaller tire diameters. Otherwise, I run into the problem of occasionally pulling them out from under the tire while handling the pressure washer hose. Thanks and regards, Mikei

The designer has replied

@optivex

Hello! that is definately something I will look into, thanks for the feedback!

@Streiti

Boosted

Replying to @optivex :

Thanks, that´s great.

@Streiti

Boosted

Replying to @optivex :

Have you found the time yet to see if you can change it?

@user_2584503870

Print Profile

0.4mm nozzle - 0.2mm layer, 5% gyroid, 4 walls

@sigep93

Boosted

This makes me so mad when the hose gets stuck, I boosted before I even printed.

The designer has replied

@optivex

Legend!

@Romans1x16

Absolutely genius! Getting the pressure washer hose caught underneath the tire is always so depressing, especially when you can’t flick the hose to get it out, haha. Definitely going to print one, or a few, soon.

The designer has replied

@optivex

Thanks alot!

@user_58009971

Print Profile

0.4mm nozzle - 0.2mm layer, 5% gyroid, 4 walls

nice and sturdy. If the top part where the tire is was rounded like the floor part help a little.

The profile uploader has replied

@optivex

I will take that into consideration if I make a newer version, I have recevived other feedback too which I could incorporate! Thanks!

@celiow

Good evening, would it work in PLA as well, or is PETG the real recommendation

The designer has replied

Show original

@optivex

PETG is the reccomendation, at minimum something like PLA tough. It would probably work Ok in PLA just increase to 5 walls or so, but be mindful that it might warp due to moisture or heat over time, so you may need to reprint at some point.

@user_2895652518

Print Profile

0.4mm nozzle - 0.2mm layer, 5% gyroid, 4 walls

The print was awesome. I can't wait to give them to my son in-law.

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Car Wash HOSE GUARD

Fredrik88

3.4 k

1.3 k

A1/A1 mini Cable elastic conduit

ShapeX

96.2 k

15.8 k

A1 Hotend Cable Chain (Updated)

Moskk83

24.3 k

8.8 k

Cable Organiser/Cable Clip

Epiq3D

22.5 k

4.4 k