PROP FTN.5 Rimfire Suppressor Remix - Free 3D Print Model

Search models, users, collections, and posts

Braden W.

Hobby & DIY>Sport & Outdoors

IP Report

Print Profile(1)

All

P2S

H2S

X1E

P1S

P1P

X2D

A1 mini

H2D

X1 Carbon

H2C

H2D Pro

A2L

0.16mm layer, 6 walls, 99% infill

Designer

24.9 h

2 plates

4.9(8)

Open in Bambu Studio

Boost

146

577

353

131

Released

Description

This is a prop or for airsoft use ONLY. Do not attach this to any sort of firearm.

I WILL HAVE NEW DESIGNS COMING SOON, IF YOU LIKE THESE MAKE SURE TO HIT THAT FOLLOW BUTTON TO BE NOTIFIED WHEN MY NEW RELEASES ARE OUT

V2 UPDATE NOTES 5/17/2026

Added a pocket for a washer to fit into for engraving, washer dims are 1.375" OD and 0.03" thick
Added ¾"-16 thread on second plate for those that wish to go that route
Changed print profile, this one should turn out better looking and sturdier, but if you printed V1 it is absolutely fine

My personal remix of the FTN.5 Rimfire from PLABoi. This thing is QUIET with subs. Added texture to the outside, made it a direct thread for ½"-28, baffles are the same as standard FTN.5. File is preoriented and ready to run as is. No post processing required. PLA+ or nylon filaments only! NO PETG.

Remember to follow all local, state, and federal laws, and I am not responsible if you create one of these without the proper documentation.

Everything I make is exclusive to Makerworld, so if you see my designs other places, please notify me ASAP, thank you!

Boost Me (for free)

If you like my designs please drop a boost, like, and leave a rating so I can continue to release my designs to you for free! Thank you!

Comment & Rating (48)

@user_3267655321

Print Profile

0.16mm layer, 6 walls, 99% infill

The profile uploader has replied

@thereal526

did you have an issue with the print?

@user_3267655321

Replying to @thereal526 :

the thread was a little tight and there was a little stringing at the end but that could be my filament, I works very well

@thereal526

Replying to @user_3267655321 :

Ah okay, yes the threads are meant to be the tightest tolerance I could design to assure that they were snug, not something you want coming off unexpectedly lol! And the stringing is probably a calibration thing, what were you using? I noticed that Sunlu filament on these didn’t seem to do as well as Bambu PLA Tough +

@user_1407496086

DO NOT PRINT THIS UNLESS IF YOU WANT TO GO TO PRISON. ( or have applied for an ATF Form 1 and have a tax stamp to show for the specific "can" you want to make..

The designer has replied

@thereal526

If you read the description I said make sure you follow all local state and federal laws

@user_1407496086

Replying to @thereal526 :

that comment is for the people who won't realize what that disclaimer really means. already files form 1 paperwork, so as soon as it clears, I'm making this.

@thereal526

Replying to @user_1407496086 :

You’ll have to come back and let me know what you think once you get it if you remember! I’m beyond impressed for the small amount of PLA+ used

@powtyplays

bro no way this is illegal. but still might print

The designer has replied

@thereal526

this is not illegal in the US, it is a suppressor, and with an approved Form 1 it is perfectly legal. that’s why the description says please follow all federal, state, and local laws

@Gunsmoke

@powtyplays Tell us you have no clue about laws or the NFA, without telling us you have no clue! 🙄🤦🏼‍♂️

(Edited)

@CincyDesigns

Boosted

Replying to @thereal526 :

I am going to download this, but just to let you know, this is against the Makerworld Community guidelines since it is a functional weapons part. Thought to let you know before your account gets banned.

@user_449731182

Boosted

I love the design but can you make one with a 1/2 by 28 to a 16 by 3/4”. be a whole lot easier for me with metal threads

(Edited)

The designer has replied

@thereal526

Well I can’t put two threads onto it, so I’m not sure what you’re asking for? I can make one with 3/4”-16 threads sure

@user_449731182

Boosted

Replying to @thereal526 :

That is what I meant. sorry for the confusion. thanks again

@thereal526

Replying to @user_449731182 :

no worries, I’ll get it uploaded tomorrow night and reply here when it’s on there!

@Wilderfarmstead

why not PETG?

The designer has replied

@thereal526

when PETG fails it shatters, probably not a huge deal for rimfire, but in general I stay away from PETG for anything 3D2A

@Wilderfarmstead

Replying to @thereal526 :

good to know! I haven’t printed anything along these lines.

@thereal526

Replying to @Wilderfarmstead :

PLA+ minimum for rimfire suppressors. PA6-CF minimum for pistol or centerfire rifle calibers with PPA-CF being preferred. PETG is fine for NON functional items, rail covers, foregrips. Receivers should be minimum PLA+

@user_93678914

Boosted

top

The designer has replied

@thereal526

Thanks for the boost!

@user_223704946

will this work for a .22 air gun?

The designer has replied

@thereal526

I have no idea

@user_1407496086

probably not. airguns operate differently.

@user_2824590696

don’t you want to have it print at a shallow angle instead of vertical? or is it okay since it’s 22lr

The designer has replied

@thereal526

doesn’t matter there’s 0 pressure

@RNGFishing

Print Profile

0.16mm layer, 6 walls, 99% infill

great print.

@big_M44

Print Profile

0.16mm layer, 6 walls, 99% infill

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.