SaitoSquare

cover

Skadis_Shelf16x8_02_a788dd46-d2ce-42cb-b163-fc4427394898.jpg

plate_1.png

16x8.png

base.png

v3-6_change.png

Generic PLA setting.  V3 has a bespoke support modelled - no auto support necessary.&nbsp;Update: V3_14 (25 Dec 2024) : Added a base strip where the 4 supports sit on to improve adhesion.  Also added 2 ‘pins’ to improve stability for the hook part.  Thank you, <a target="_blank" href="https://makerworld.com/en/@Dpfei2024" rel="nofollow noopener">@Dpfei2024</a>, for pointing out the problem - I hope this version addresses the issue!! &nbsp;Update V3_8 (10 Nov 2024) : Adjusted the tightness by making the bump slightly smaller - now it is not too tightly fit. (thank you for your comment, <a target="_blank" href="https://makerworld.com/en/@user_4110259357" rel="nofollow noopener">@user_4110259357</a>).  Also small improvement on the support which should snap off a lot easily.&nbsp;Update V3_6 (22 Sep 2024) : improved the strength of the hooks by changing its shape to be more square, which was suggested by <a target="_blank" href="https://makerworld.com/en/@Gfox0622" rel="nofollow noopener">@Gfox0622</a> (Thank you!!) and changed the wall loops to be 3 to fill the inside of the hook better. (see A) Also, created a bespoke support that can be snapped off easily (see B). (still need a gentle but firm pressure to break it off) I hope this change would address the weakness of the hook which were pointed out by the fantastic people here!  Thanks again for all the learning opportunity, guys :)   It took me this long but it was worth it :)&nbsp;Update (13 May 2024) : the support type is switched from ‘tree slim’ to ‘tree organic’ which makes the detaching far easier.  Thank you, @hansdiegans , for point this out for me :) :)

0.2mm layer, 3 walls, 15% infill

16x8_noDots.png

base.jpg

16cnX8cm_no_dots_2_c632e475-ed03-4edf-bdc8-59774dd4c373.webp

This version has no dot in the middle, suitable for the bottom row of your Skadis board. Generic PLA setting.  V3 has a bespoke support modelled - no auto support necessary.&nbsp;Update: V3_14 (25 Dec 2024) : Added a base strip where the 4 supports sit on to improve adhesion.  Also added 2 ‘pins’ to improve stability for the hook part.  Thank you, <a target="_blank" href="https://makerworld.com/en/@Dpfei2024" rel="nofollow noopener">@Dpfei2024</a>, for pointing out the problem - I hope this version addresses the issue!! &nbsp;Update (22 Sep 2024) : improved the strength of the hooks by changing its shape to be more square, which was suggested by <a target="_blank" href="https://makerworld.com/en/@Gfox0622" rel="nofollow noopener">@Gfox0622</a> (Thank you!!) and changed the wall loops to be 3 to fill the inside of the hook better. (see A) Also, created a bespoke support that can be snapped off easily (see B). (still need a gentle but firm pressure to break it off) I hope this change would address the weakness of the hook which were pointed out by the fantastic people here!  Thanks again for all the learning opportunity, guys :)   It took me this long but it was worth it :)&nbsp;Thanks to <a target="_blank" href="https://makerworld.com/en/@geniejhang" rel="nofollow noopener">@geniejhang</a> - who made me realized that the middle dots would get in a way if you would position the tray at the bottom row. This version can fit anywhere on the wall.&nbsp;Update (13 May 2024) : the support type is switched from ‘tree slim’ to ‘tree organic’ which makes the detaching far easier.  Thank you, @hansdiegans , for point this out for me :) :)&nbsp;

- no middle bumps - 0.2mm layer, 3 walls, 15% infill

gertyengrie

IMG_20250130_145723_HDR.jpg

2 x no bumps - 0.2mm layer, 2 walls, 15% infill

Oliver

2024-07-07_df0f3c0020608

0.8mm nozzle, 0.4mm layer, 2 walls, 10% infill

Long shelf 1

Long shelf 2

plate_2.png

Extra lips single shelf

plate_3.png

BjoBor

skadis_shelf_long_more_lip_2.png

skadis_shelf_long_more_lip_1.png

skadis_shelf_more_lip_1.png

<ul><li>Made a split tray for A1 mini that becomes 27,9cm total when combined.- Do note that the split will be visible, I am using it for tools and not display.- Keep the negative shape as is to have no lip in the middle of the tray  </li><li>Made one tray same size with more lip on the sides and front so items are more secure.</li></ul>0.2mm layer, 3 walls, 15% infill

A1 mini 28cm (split) tray, extra lip tray

64dtz

20260510_183318.jpg

20260510_183302.jpg

Smooth - No Ridge / Lip

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

16cm x 8cm small shelf panel for IKEA Skadis board. The fixture is snug fit providing a very sturdy platform for displaying small objects.A small bump is added in the middle for extra security. The panels can be placed side by side. Works with the <a target="_blank" rel="noopener noreferrer ugc" href="https://makerworld.com/en/models/250370#profileId-266599">8cm x 8cm</a> and <a target="_blank" rel="noopener noreferrer ugc" href="https://makerworld.com/en/models/2162715-ikea-skadis-shelf-panel-24cm-x-8cm-sturdy#profileId-2344886">24cm x 8cm</a> as well.

IKEA Skadis Shelf Panel (16cm x 8cm) - Sturdy

ASIA

Print Profile(6)

Description

Comment & Rating (332)

License

Related Models