Hitster Tower v2 - Free 3D Print Model

Search models, users, collections, and posts

TheHolgi

Toys & Games>Other Toys & Games

IP Report

Print Profile(3)

All

P2S

H2D

P1S

A1 mini

H2S

H2C

P1P

X1 Carbon

X1E

H2D Pro

X2D

A2L

0.2mm layer, 2 walls, 7% infill

Designer

7.6 h

3 plates

4.9(51)

Privacy cover 0.2mm layer, 2 walls, 15% infill

Designer

45 min

1 plate

4.4(7)

Print profile with 36mm tube for the larger cardboard chips

Designer

2.7 h

1 plate

4.0(2)

Open in Bambu Studio

Boost

102

478

137

672

512

Released

Bill of Materials

Bambu Filaments

Select all

PLA Basic

Description

Content has been automatically translated.

Show original

Here is the second revised version of the Hitster Tower. I have incorporated wishes and suggestions and made some optimizations for better quality and reduced print time. The print profiles have been adjusted so that no “extra” or Support for PLA is needed anymore. The top part is slightly offset, as there were apparently problems scanning with some mobile phones. Cutouts for the speakers have now also been added. I have distributed the parts across 3 print plates:

Tower for the larger chips of the Celebration Edition.
Tower for the "normal" chips.
Top part suitable for both versions.

Boost Me (for free)

I would be very happy about a "BOOST" 😊

I have added a matching lid upon request.

Upon request, I have also added a tower with a 36mm tube for the slightly larger cardboard chips, which are apparently sold in the Netherlands. I have now learned that the larger chips are also sold in Germany in some cases. It is advisable to measure the diameter of the chips or to print the tower for the 36mm chips directly, as this version should also be compatible with the smaller chips.

Comment & Rating (137)

@Goerni

I will probably only rate this with a maximum of 2 stars here (as soon as possible) The German "normal" tokens are 35 mm Unfortunately, that doesn't fit The normal tokens are too big I think if you had just made one variant with 36.5mm, all the chips would fit and the frustration wouldn't be so great Nowhere does it say that you have to measure the chips beforehand That's a shame Furthermore, you cannot remove or "move" the card from the storage area at the bottom because the steps of the increase are too steep I had to carefully rework it with a Dremel for 15 minutes All in all, disappointing for me

The designer has replied

Show original

@TheHolgi

That's not correct. I am from Germany and bought the game here as well. The small version fits perfectly for me. I couldn't have known when creating the tower that there were different versions. I then created 2 more versions. If you had read the description, it might have been easier. Don't forget that I don't earn any money from this! With users like you, one can quickly lose the desire to upload anything at all

Show original

@Goerni

Replying to @TheHolgi :

Thank you for your reply. And yes, criticism is always hard. However, I have substantiated the criticism. It would have been easy to point out that one should measure the tokens beforehand and then start the 6-hour print. Sorry, but if I decide to provide something like this, I'll do it properly or not at all. And no, my goal was not for you to lose interest, of course, but my goal was for you to improve the model accordingly, adapt the description, and address the criticism. I hadn't even given a star rating yet, but only wrote the comment to prevent other users from printing for 6 hours in vain. My criticism was factual and I therefore have no bad conscience. If the criticism is addressed, I will of course gladly leave a corresponding positive rating and perhaps also a boost. Best regards

Show original

@TheHolgi

Replying to @Goerni :

Criticism is always welcome, and yes I have already addressed many requests and made changes and improvements. It just comes across a bit strange when someone writes that a maximum of 2 stars are given for it. That's fundamentally okay if you're not satisfied with the work or the model. But I will revise the description again. Perhaps everything was formulated a bit unfortunately on my part

Show original

@Rettungszwerg

very clean print qr code also recognizes it perfectly great spacing only problem I have I can't get the cards out that well

The designer has replied

Show original

@TheHolgi

Then there may still be remnants of the support in the slot. Simply rework with a craft knife

Show original

@Goerni

I feel the same way. The cards don't come out of the lower tray because the steps here are too large. I've already worked on it for 10 minutes with sandpaper, but it's still no better

Show original

@boodroosterpaul

Print Profile

0.2mm layer, 2 walls, 7% infill

added all parts to 1 plate for my p2s and printed smooth !! with a nice multicolor from bambu

The profile uploader has replied

@TheHolgi

Thank you!

@user_2497373104

Print Profile

0.2mm layer, 2 walls, 7% infill

Super glue 😁👍

The profile uploader has replied

Show original

@TheHolgi

Thank you, it looks very good in black too

Show original

@TOSHIRTCOM

Print Profile

0.2mm layer, 2 walls, 7% infill

great design functional prit

The profile uploader has replied

@TheHolgi

Thank you 🙏

@3DHausdruckerei

nice print

The designer has replied

@TheHolgi

Thank you 👍

@Sveisel80GE

Boosted

Hello, great tower could you add a lid or a closed version, so that you can no longer look down into the phone?

The designer has replied

Show original

@TheHolgi

Thanks. I will check it out

Show original

@Sveisel80GE

Boosted

Dankeschön

@TheHolgi

Hello, I have created a lid. I have uploaded the print profile

Show original

@Goerni

Print Profile

0.2mm layer, 2 walls, 7% infill

Please be sure to measure the tokens beforehand! With me it was unfortunately too small (German Hitster version)

The profile uploader has replied

Show original

@TheHolgi

Hello, it is probably the case by now that different versions or diameters of chips are also sold in Germany

Show original

@Goerni

Replying to @TheHolgi :

Thanks for adjusting the description

Show original

@nicooltje

does the iphone also fit?

The designer has replied

@TheHolgi

Yes, testet with iphone 16 pro and iphone 15 pro max.

@nicooltje

Replying to @TheHolgi :

I printed it, but the first time I printed it, there were loose wires where the cards slide through and where the coins go through. So I had to add support. Am I doing something wrong?

@TheHolgi

Replying to @nicooltje :

It’s not possible without support. My print profile also includes support

Show original

@user_1773835078

Print Profile

0.2mm layer, 2 walls, 7% infill

Very helpful. Thanx.

The profile uploader has replied

@TheHolgi

Thank you for the 5 ⭐️

Show original

License

This user content is licensed under the MakerWorld Exclusive License.

You may create derivative works based on this object, provided that all such derivative works are published exclusively on the MakerWorld platform and include proper attribution to the original creator. You may not share, upload, host, distribute, or publish this object—or any derivative work of this object—on any other digital platform, marketplace, or distribution channel. Commercial use of this object and any derivative works is strictly prohibited. This includes, but is not limited to, selling, renting, sublicensing, or using the object in any context in which you receive monetary compensation or other financial benefits.

Related Models

Hitster Tower V2

Printy McPrintFace

5.7 k

812

Smash! The Auto-Reload Dice Tower

Rossero

24 k

11.5 k

Calibration Tower PETG

Xeraj

31.2 k

1.8 k

PLA temp tower 195 up to 220

MikeProch

23.3 k

1 k