A1 Mini Z Carriage Dust Shield

A1 Mini Z Carriage Dust Shield

Boost
70
181
34

Print Profile(1)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

0.2mm layer, 2 walls, 15% infill, Ironing
0.2mm layer, 2 walls, 15% infill, Ironing
Designer
8 min
1 plate
4.5(23)

Boost
70
181
34
0
186
55
Released

Description

Dust shield for the Z carriage of the A1 mini. This prevent dust from entering inside the lubrication hole on the top of the carriage.

You can use double sided tape for a better fixation.

Comment & Rating (34)

Please fill in your opinion
(0/5000)

Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
no issue with print
The designer has replied
1
Reply
Very clean print 👌 Thanks for sharing it with us ;)
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
An und fürsich gut nur hält es logisch nicht von alleine und für die Schrauben passen die Löcher nicht aber für die Idee 3 sterne
The designer has replied
0
Reply
Hello, the 2 holes aren't design for the screws but for the two little pin on the carriage. If you want to fix the dust cover use double sided tape. I recommend you to use the smooth build plate for a better result. And for your info, ratings are for the print profile itself not the model ;)
(Edited)
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
perfect fit
0
Reply
Bummer it doesn't fit for me the screws are domed not flat like the others.
The designer has replied
0
Reply
Thanks for the feedback so the screws aren't flush with the side of the carriage? Maybe there are some variations amongst the carriage used. Could you send a picture of your carriage ?
0
Reply
Replying to @Henlor :
of course here they are I think it’s bc the screws on my printer are domed and not flat a the top of the screw
0
Reply
Replying to @Psych :
Indeed those are different from mine. Thank I'll see what I can do about this ;)
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
good design but too loose, Ocular Dynamic's remix has a better grip without tape https://makerworld.com/en/models/417343#profileId-319712
The designer has replied
0
Reply
Thanks. I didn't print this remix but before releasing my model, I tried to add a pin to lock it in place inside the hole. I from my testing I've found this feature too weak and could eventually break inside the hole. So I preferred to release my model without any pin. So you know ;)
(Edited)
1
Reply
Replying to @Henlor :
good point, thanks for your feedback. I still like your designs, keep it up ✌️
0
Reply
Replying to @D4V3IG :
Thank you ;)
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
Printed okay, just doesn’t really attach to the printer at all.
The designer has replied
1
Reply
Sorry I'm replying super late. But yes indeed, you need to use double sided tape if you want to fix it. Or if you don't mind, you can leave it on top and let the gravity do its thing (that's what I'm doing)
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
maybe a bit to thin
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
good!
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
not fitting right
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill, Ironing
Good print profile, but the part not fit well
0
Reply