Search models, users, collections, and posts

RC Remote Control Patrol Boat (Jet Version) Hull V1

PathfinderANT
Hobby & DIY>RC
IP Report

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
H2D
H2D Pro
H2S
P2S
H2C
X2D
A2L
0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
37 h
7 plates
5.0(2)
Open in Bambu Studio
Boost
212
483
40
12
635
35
Released 

Description

Content has been automatically translated.
Show original

Remote Controlled Destroyer (Jet Edition) Hull V1

1. It is recommended to use ABS or ABS+ or PETG as the printing material for the model, avoiding the use of brittle materials such as PLA.

2. Accessories include a brushless motor (2216 brushless motor RC450 helicopter, boat version), waterproof drive shaft (sleeve outer diameter 8mm) 150mm version, universal joint (note matching motor and drive shaft size), ESC, remote control and receiver, M3 screws, some wires, etc.

3. The model is not for distribution, only download on this platform.

4. This link is the model main body link, accessories link: https://makerworld.com/zh/models/216203#profileId-235316

Remote Control
Remote Control Speedboat
Destroyer
Boat
Jet
Jet Boat
Speedboat
Remote Control Boat

Comment & Rating (40)

(0/1000)
@user_3692816982
Hello! my dad and I have prited your work,and we have found something wrong.1.the contact area be tween models, is too small. 2. the repair window is inconvenient, the hull can only be assemled by bonding, it's hardly to repair by the repair window. 3.the installation position of the nozzle directional not designed. my dad and I like the ship very much and we will try our dese to make it sail!
The designer has replied
3
Reply
@PathfinderANT
Thank you very much for your feedback regarding the overall boat model issue which I also noticed through your analysis because sometimes when I make boat models or aircraft models I address defects through later modifications as I am not a professional designer some issues are difficult for me to foresee and are only discovered when the official model is printed and assembled Thank you again for your understanding if there are any design flaws and you and your father need the original model you can leave me a message and I will be happy to assist you Finally I wish you success experience and immense joy in this model-making process
Show original
3
Reply
@Druckersohn
Replying to @PathfinderANT :
Hello, I'm wondering why the hull has gaps along the bottom edge
Show original
0
Reply
@user_1619945460
super
Show original
0
Reply
@user_1619945460
👍
0
Reply
@MistyThePig
Very nice
1
Reply
@Druckersohn
Where can one find the printer accessories The link is for an A......
The designer has replied
Show original
0
Reply
@PathfinderANT
Could you provide me with your email address so I can send it to you
Show original
0
Reply
@Druckersohn
Replying to @PathfinderANT :
Yes please manuelbierbacher72@gmail.com and inquire why the hull has gaps the edge is not printing correctly it is open and water could ingress Kind regards Manuel
Show original
0
Reply
@PathfinderANT
Replying to @Druckersohn :
This gap is insignificant, however, material seepage might occur, it is recommended to use a spray-on waterproof sealant, applying a layer inside the hull
Show original
0
Reply
@user_1619945460
🆗
0
Reply
@user_2324910547
How much is the budget
The designer has replied
Show original
0
Reply
@PathfinderANT
You mean filament cost or electronic equipment filament cost has not been calculated electronic equipment around 200 but this electronic equipment can be reused
Show original
0
Reply
@user_3327721224
Replying to @PathfinderANT :
Is there a link for electronic devices
Show original
0
Reply
@user_3327721224
Is your ship ready
Show original
0
Reply
@hyxs
Hello OP, this boat doesn't have motor water cooling, can it be added
The designer has replied
Show original
1
Reply
@PathfinderANT
I was using a brushless motor at the time, so water cooling was not considered
Show original
0
Reply
@user_2737030081
Hello, I am making this model you published, could you provide contact information for communication
The designer has replied
Show original
0
Reply
@PathfinderANT
693737939
0
Reply
@user_3327721224
Are the accessories installed
Show original
0
Reply
@Druckersohn
Which drive shaft was used Or is there a propeller with m3 mountings available
Show original
1
Reply
@user_3975904763
Hello, could you provide a parts list
The designer has replied
Show original
0
Reply
@PathfinderANT
Let's hold off on this one; the RC response seems problematic
Show original
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

BMW M4 G82 — 1:10 Scale Model/RC Car
BMW M4 G82 — 1:10 Scale Model/RC Car
Cormango
9.7 k
8.2 k
Dummy 13 V1 Kit Card
Dummy 13 V1 Kit Card
Vasichkin
27.1 k
5.6 k
Board Hook V1
Board Hook V1
Mohammad AD
20.1 k
6 k
Print in place gravity knife V1
Print in place gravity knife V1
Make it work.
9.1 k
2.5 k