Adjustable Phone Holder - Vertical or Horizontal - Has access to use with phone plugged in by rennim

rennim

Household>Office

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

0.4mm nozzle, 0.20mm layer, 3walls, 15% infill

Designer

2.2 h

2 plates

4.1(21)

Open in Bambu Studio

Boost

115

335

304

Released

Description

EDIT 3/9/2024: I created a remix of my phone model to introduce a number of improvements. People reported the printed bolts breaking trying to tighten them sufficiently to hold the stand fixed in place. New model adds notches at the two key interfaces that take all of the load. The bolts serve to keep the pieces from sliding apart, but take very little load and require very little tightening.

I recommend using the updated model:

https://makerworld.com/en/models/242128#profileId-258073

Adjustable phone holder. Allows for the height and angle to be adjusted. Can also be collapsed or disassembled for easy transport.

Phone can be held horizontal or vertical.

Has access for charging cable out the bottom.

Prints without any support or brim.

Comment & Rating (37)

@zackjessie

Print Profile

0.4mm nozzle, 0.20mm layer, 3walls, 15% infill

printed good. wonder if upscaling would work for an ipad

The designer has replied

@rennim

i think you'd have issues with getting enough clamp/friction. if you rough up the contact surfaces or otherwise increase friction (squish a rubber band in between?) it should work.

(Edited)

@zackjessie

Replying to @rennim :

yeah I took some time last night after having to tighten a screw to much and it broke. here is an idea if your interested works pretty good, need tweaks.

@rennim

Replying to @zackjessie :

I took your suggestion and added similar notches to an updated version of the model: https://makerworld.com/en/models/242128#profileId-258073 I also made a second version that has a wider base to accept thicker phones: https://makerworld.com/en/models/242131#profileId-258080 Thanks for the pointer! In the new version the notches take all of the load, the bolts are just there to keep the notches from sliding apart and take very little tightening. Works great with everything printed from PLA.

(Edited)

@nightclaw

Print Profile

0.4mm nozzle, 0.20mm layer, 3walls, 15% infill

Works and prints great but like mentioned in another comment could need some ridges for holding the arms in place

The designer has replied

@rennim

check remixes. I uploaded 2 new version both with notches to anti rotate the arms. one 12 mm max phone with and the second 16 mm max phone width. the bolt in the notched version doesn't need to be tightened because the notches take all of the load. so you can print the bolt out of pla at low infill.

(Edited)

@YAN3D

Print Profile

0.4mm nozzle, 0.20mm layer, 3walls, 15% infill

可以，比较实用

(Edited)

@eztbucket

Print Profile

0.4mm nozzle, 0.20mm layer, 3walls, 15% infill

bolts are not useable at all

(Edited)

The designer has replied

@rennim

worked great for me. try petg at 100% infill per my print profile. PLA can't be tightened enough.

(Edited)

@modrosonce

works for me at 25% infill no problems

(Edited)

@rennim

Care to comment as to why the bolts are not usable? everybody else has had zero issue and I don't appreciate the zero star review. I've printed 5 of the older version that you printed and they all worked great. I uploaded a new version with notches at the interface so the bolts don't need to be tightened very much at all - see below: https://makerworld.com/en/models/242128#profileId-258073

@felefrancesco

Print Profile

0.4mm nozzle, 0.20mm layer, 3walls, 15% infill

le viti si sono rotto

The designer has replied

@rennim

try the improved remix. you will not need to tighten the bolts at all. works perfect.

@pcmike

Will this hold the phone in full 90deg? Looking for something that will hold completely upright (90deg) or even fall backwards a little to capture time lapse sunrises.

The designer has replied

@rennim

90 degrees likely. but it would be tipsy. it definitely can't hold the phone leaning forward.

@user_3871211826

Print Profile

0.4mm nozzle, 0.20mm layer, 3walls, 15% infill

buonissimo progetto ma ho modificato la vite di fissaggio

The designer has replied

@rennim

If you say it's "very good" why did it only get 3 stars? Also I already created an updated remix with notches that hold the structure in place without needing to tighten the bolt. Check remixes to this model.