Search models, users, collections, and posts

Sonoff Zigbee 3.0 Dongle Magnet Mount Hex

aasccr08
Hobby & DIY>Electronics
IP Report

Print Profile(2)

All
X1 Carbon
X1
H2D
X1E
P1S
P1P
A1 mini
A1
H2D Pro
H2S
P2S
H2C
X2D
A2L
0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
42 min
1 plate
4.9(14)
USB 2.0 Extender Magnetic Guide
USB 2.0 Extender Magnetic Guide
Designer
43 min
1 plate
5.0(1)
Open in Bambu Studio
Boost
40
171
18
2
231
146
Released 

Description

Magnetic Mount for the SONOFF Zigbee 3.0 USB Dongle Plus Gateway:

https://www.amazon.com/dp/B09KXTCMSC?ref=ppx_yo2ov_dt_b_fed_asin_title

 

Not really held by anything other than the USB extender that is attached to it. Should not matter what type of extender, but I used this:

https://www.amazon.com/dp/B00N9HRTFU?ref=ppx_yo2ov_dt_b_fed_asin_title

 

Uses two 20x3mm magnets, like this:

https://www.amazon.com/dp/B0CZ71S5ZP?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

 

Print in PETG or PLA. Also added the USB wire magnet mount in the profile. Use 10x4mm magnets pressure fitted.

sonoff
sonoff accessory adapter
zigbee
zigbee mount
magnet
mount

Comment & Rating (18)

(0/1000)
@kosejk.radek
Print Profile
0.2mm layer, 2 walls, 15% infill
fits like a glove 🤌 I had adjusted the back side a little (just added a thin plate in slicer) because I wanted to you velcro tape, and the magnet holes would prevent that.
1
Reply
@user_3296587355
Can you please upload your version? I would like to do the same with velcro instead of magnets.
0
Reply
@kosejk.radek
Replying to @user_3296587355 :
https://makerworld.com/en/models/2280982-sonoff-zigbee-3-0-dongle-velcro-power-strip-mount#profileId-2487400 here it is
0
Reply
@user_3296587355
Replying to @kosejk.radek :
Thank you so much. Once my printer is done with its current job, I’m going to print this and boost you :)
(Edited)
1
Reply
@Giadenant
Print Profile
0.2mm layer, 2 walls, 15% infill
Great, fast, and very practical
Show original
0
Reply
@neyer_89324879
Print Profile
0.2mm layer, 2 walls, 15% infill
passt perfekt!
0
Reply
@SenorPantalones
Print Profile
0.2mm layer, 2 walls, 15% infill
Prints and fits great. I had to trim some extra plastic from my USB extension port but I'd rather that than it fitting too loose honestly.
0
Reply
@user_3527165162
Print Profile
0.2mm layer, 2 walls, 15% infill
works and fits well, almost too tight but better than if it's too loose
Show original
0
Reply
@HaMa_Au
Print Profile
USB 2.0 Extender Magnetic Guide
Perfekt fit.
0
Reply
@tamet83
Print Profile
0.2mm layer, 2 walls, 15% infill
ottimo
0
Reply
@u_harbich
Print Profile
0.2mm layer, 2 walls, 15% infill
passt wie angegossen
0
Reply
@La_Psycobill
Print Profile
0.2mm layer, 2 walls, 15% infill
Top, macht was es soll
(Edited)
0
Reply
@kristof24
Print Profile
0.2mm layer, 2 walls, 15% infill
0
Reply

License

This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike

Remixes (3)

Sonoff Zigbee 3.0 Dongle Magnet (6x2) + USB holder
Sonoff Zigbee 3.0 Dongle Magnet (6x2) + USB holder
tamet83
5
2
Sonoff Zigbee 3.0 Dongle 1U Rack Mount
Sonoff Zigbee 3.0 Dongle 1U Rack Mount
Bedtime
140
27
Click to see more

Related Models

Mini Hex Fidget!
GIF
Mini Hex Fidget!
JMedow
19 k
5.6 k
Bambu Reusable Hex Spool
Bambu Reusable Hex Spool
Brandido02
20.8 k
2.9 k
Hexagon Fidget
GIF
Hexagon Fidget
Printer King
21.6 k
2.3 k
Gridfinity Hex Bins all sizes
Gridfinity Hex Bins all sizes
ostat
26.5 k
4.9 k