Baby Dino Trio – Anabel, Samara & Tomek(no suppor)

Thank you all for your support. I'm always happy to hear your opinions and suggestions for new models. So please share them in the comments.

You can offer me a coffee and support my work here >>> https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support. The website also includes a commercial license that allows you to sell all my existing models.

https://ko-fi.com/drakeforge3d  If you like my work and want to support me, I appreciate any support.

Printed Baby Dino Trio – Anabel, Samara & Tomek

Meet the cutest prehistoric family you’ve ever seen! This delightful 3D printed trio brings together:

•  Anabel the Baby Triceratops – Curious and courageous, she’s always leading the group into tiny adventures.
•  Samara the Baby Ankylosaurus – Tough on the outside, sweet on the inside, Samara is always ready to protect her siblings.
•  Tomek the Baby Brachiosaurus – Tall and gentle, Tomek loves to reach for the stars… or at least the top shelf.

These adorable baby dinosaurs are optimized for fast FDM 3D printing with no supports required. Each model prints in under 30 minutes, using minimal filament (typically under 7 grams), and still looks great at a 0.2 mm layer height.

Perfect for kids, collectors, and dino-lovers of all ages — this miniature family is ready to stomp straight into your heart.

Tiny roars. Big smiles!

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

•  

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support

     Guide

Each of my models is printed 2-3 times before releasing the profile. So if you have a problem with printing:

1. DRY THE FILAMENT
2. CHANGE THE NOZZLE TO A NEW ONE.

Recommendations  Guide : In case of a problem with damage to the supports, I recommend reducing the printing speed of the supports by 30-50% and the travel speed to 400mm/s. When removing the supports, I recommend first cutting off the pieces right next to the character, but not removing them, just cutting them off. Remove the remaining larger pieces and only then detach the remaining smaller pieces. This reduces the risk of damaging delicate elements.

• Please note that if you use a different filament than the recommended one, the effect may be different from my print. For example, printing in silk PLA will look better but the supports and the print itself will be more brittle and less durable.

   

   

  Recommendations:

• 
   
• 0.08-0.2. In the event of changing the original height, the height of the supports should be changed.
   

• PLA+HS, PLA+, PLA, PLA silk Recommended materials are listed in order from best to good.

   

• Clean the plate thoroughly before printing.
  Make sure the filament is dry and free from dirt. This can damage the print or weaken the support