Search models, users, collections, and posts

Tamiya Screwdriver Case for "Tamiya 74023"

Sakul
Tools>Hand Tools
IP Report

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini
H2D
H2D Pro
H2S
P2S
H2C
X2D
A2L
0.2mm layer, 3 walls, 15% infill
0.2mm layer, 3 walls, 15% infill
Designer
10.2 h
2 plates
4.7(13)
Open in Bambu Studio
Boost
107
219
22
10
153
54
Released 

Description

This is one of the oldest screwdriver sets I own, and the tools are still holding up well.

However, the thin plastic case recently broke, so I designed a new case for it.

All you need is 8 M3x20 screws and 8 M3 nuts for the mechanism.

A piece of TPU can be inserted as a seal, but that is optional.

Tamiya
screwdriver
case
set
74023
tools
box
rc
car

Comment & Rating (22)

(0/1000)
@tuxstang
Printed it scaled +10% to fit toolset 74085 ... a bit too tall but it works.
1
Reply
@datawireguy
do you think +8% would of worked better? I have the 74085 tools and want to print this case.
0
Reply
@tuxstang
Replying to @datawireguy :
Not sure ... at 10% there's sure room for the handle but not that much for the "bits".
0
Reply
@Kira_Yumi
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Fits perfectly the old Tamiya Craft Tools set But unfortunately not the new one as the tool grip is about 2 mm wide in diameter and 1cm taller and the bits are about 0.5mm wider in diameter If its possible could you make an updated version for the New Tamiya Craft Tool set too
1
Reply
@RolfXray
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Thank you for your effort, fits perfectly 👍
Show original
0
Reply
@fastcat
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
Nice idea and design, but I had to filling a lot to the handles fit nicely with no scratches on it. Thanks
0
Reply
@Aaron_Keene21
Print Profile
0.2mm layer, 3 walls, 15% infill
Excellent! 8.5-hour print with 0.4 nozzle, very sturdy. Tamiya 74023 tools fit perfectly, no rattling. Clips securely grip bolts. Tweaks: * Curve top lid & bottom hinge for easier opening/closing. Current design hinders free movement, causing lid to rub against case & tools. * Logo: Red filament bleeds. White looks better, but font & alignment need improvement. Stars should touch for a cleaner look.
0
Reply
@JZDABOSS
had to sand down the corners near the hinges as they pinch too tightly, if you get a chance, would be nice to round or chamfer these corners.
0
Reply
@JZDABOSS
Print Profile
0.2mm layer, 3 walls, 15% infill
0
Reply
@Paul_Paulsen
WARNING! This is junk, the set unfortunately does not fit because the housing is too small
The designer has replied
Show original
0
Reply
@Sakul
Oddly, it fits perfectly for me, as you can see in the images. This is likely due to the choice of filament. I find it quite disrespectful to dismiss others' work as rubbish. However, in the anonymity of the internet, everyone suddenly feels emboldened.
Show original
1
Reply
@Paul_Paulsen
Replying to @Sakul :
I suggest reviewing the comments, as several users have already noted that it does not fit
Show original
0
Reply
@user_2300091255
Print Profile
0.2mm layer, 3 walls, 15% infill
sized it down to 90% I believe, works perfect, added a little foam on the top of the lid to prevent rattleing!
1
Reply
@Balu309
Boosted
Print Profile
0.2mm layer, 3 walls, 15% infill
The print is excellent, but a design modification is necessary to ensure the lid opens correctly. The support strut at the rear of the lid and base must be rounded to allow the lid to open and close properly. It currently catches. The Tamya logo is also poorly implemented and should be revised.
Show original
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Slim Passport Case
Slim Passport Case
Wet PLA Guru
14.3 k
7.5 k
Flexi Corn Cob - Pencil case
Flexi Corn Cob - Pencil case
3dnetic
16.9 k
5.6 k
Q-tip travel case
Q-tip travel case
FlugtN
13.1 k
5.1 k
Toothbrush Travel Case
Toothbrush Travel Case
angrelou
34.8 k
9.3 k