AMS Wallmount - 3 Segment Side version Remixed by Pretzel 3D

Remixed by

Pretzel 3D

3D Printer>3D Printer Accessories

Print Profile(3)

All

P1P

P1S

X1 Carbon

X1E

0.2mm layer, 5 walls, 45% infill

Designer

7.8 h

2 plates

4.6(17)

0.2mm layer, 5 walls, Color Change

5.3 h

2 plates

4.6(5)

0.2mm layer, 5 walls, 45% infill

8.4 h

2 plates

5.0(3)

Open in Bambu Studio

Boost

154

299

167

Released

Description

A remix as i wanted to do a wall mount but this version didn't fit my AMS which had 3 gaps on each side vs the 4/5. I also flatterned the circle pattern in the centre to print cleaner.

I have add just the right hand version which you can mirror for the left hand side.

I also had to extend the distance from the wall so there was enough gap for the cable

Comment & Rating (47)

@medicd

Boosted

This looks like a double, do you have that STL somewhere? Also, I have 1 with 3 gaps and 1 with 5 gaps, would it be possible to get your version with the clearance as the 5 gap version? Ideally, I'd like a double piece like pictured here that is 1 x 3 gap and 1 x 5 gap on the same piece.

The designer has replied

@Pretzel3D

I am working on this with someone else who has requested it so will hopefully post soon

@medicd

Boosted

Replying to @Pretzel3D :

Does yours have the same distance from the wall as StefanWox? You say that you extended the distance, so I wouldn't be able to use this side by side with his.

@average3D

Print quality is great, used Sunlu black PLA, 6 perimeters, 5 bottom/top, 25% gyroid infill with supports for the drill holes. just installed it and only then realized that the lid won’t fully open which is incredibly sad… I guess it isn’t in the description but I was expecting it anyways 😒

(Edited)

The designer has replied

@Pretzel3D

This is just a remix of another design to make it fit my AMS version, i did extend it out a bit but was worried if it was extended too far out it wouldn't be strong enought and would be liable to break. Should have a good amount of space to get filament in but yes lid won't stay open on its own unless some kind of block is designed to wedge it open

@Gerard74

Print Profile

0.2mm layer, 5 walls, 45% infill

perfect

@medicd

Boosted

Great! It looks great and secure, and saves me space.

@medicd

Boosted

Print Profile

0.2mm layer, 5 walls, 45% infill

works great. I have a 3 and 5 segment AMS unfortunately so I need to find this same distance from the wall as a 5 segment.

@Advocado

Print Profile

0.2mm layer, 5 walls, 45% infill

Great model, only the screw holes are a bit wide and thin.

@sharpenedhyster

Print Profile

0.2mm layer, 5 walls, Color Change

Did not work for my 3 slot version of AMS, but certainly would have fit the bill if it did.

(Edited)

The designer has replied

@Thibodoit

That is interesting. Could you share an image?

@sharpenedhyster

Replying to @Thibodoit :

I would think having at least 3 different sets of tooling for this nonessential part would be a bit much, but I don't make those kinds of decisions, haha.

(Edited)

@Thibodoit

Replying to @sharpenedhyster :

Wow, this is the 4th variant of the AMS slot widths that I have seen. I wonder why Bambu Labs continues to change it. Was your rating based on the non-matching geometry or the print profile? Assuming the rating you gave is for the model geometry, would you mind revising your rating based on the print quality alone? I hope Bambu Labs updates Maker World to allow rating the model itself. PS, thanks for the images!

(Edited)

@youngchino

printed this on 02/23/2024 and it did not fit my 3 prong ams that I got today. middle section is to long

The designer has replied

@Pretzel3D

do you have a photo as would be surprised they have changed their housing design again

@youngchino

sorry already mounted it using a modified file that uses the slots in the rear. my middle slot came in at 83mm

@Cuddly.Goblin

Replying to @youngchino :

I have the opposite problem. My middle section is smaller. Glad I measured prior to printing. I will add a remix in the coming days. I received my AMS April 8 2024 and a different tooling again. Good thing is they're forcing us to use fusion 360 I guess...yay more time designing lol doh!

@nikowynor

Print Profile

0.2mm layer, 5 walls, Color Change

@StefanE.

Print Profile

0.2mm layer, 5 walls, 45% infill

Beim Mittelstück: Trotz gereinigten Bett löst sich der Druck und die Stützen lassen sich nicht entfernen. Zudem viel zu viel Stützen. Eine STL ist leider nicht verfügbar.

The designer has replied

@Pretzel3D

let me check this tomorrow if there is no stl I can add it, you can also adjust the 3mf on you computer aka extract the stl from there also

@Pretzel3D

the raw STLs are on makerworld so you can try and print with different supports or reorientate, i just put two side piece together to create the central mount so was always going to be tricky with supports, but the standard supports came off fine for me. Currently i have my mounts in pla but at some point i might need to change these to PETG/ASA/ABS but will see

@alexandru.gherg

Replying to @Pretzel3D :

I am currently reprinting your remix (thanks btw) in PETG because the PLA prints just broke (scared the shit out of me). I was lucky it didn't break the glass on the printer.