Its On My Mind

cover

plate_1.png

2025-05-02_3ade79ce0bcc8.jpg

No AMS - 2 colors by object

plate_2.png

The_C

图片4.jpg

图片1.png

图片2.png

图片3.png

两盘打印的双色模型，无需 AMS，A1 mini 可用。 修复多处可能造成缺陷的悬垂和桥接。 重新绘制支撑，减少不必要的支撑，更容易拆除。 对于底面有 45°以下的悬垂，Brim 与模型的间隙应大于 0.2mm 便于拆除。 工艺参数可用于 PLA 和 PETG。默认使用 PETG HF，请自行修改为你校准过的耗材参数。 无论什么模型，始终建议打印前清洁打印板并适当涂胶，避免模型翘边、脱离导致“炒面”。&nbsp;修复问题如下：<ol><li>增加 TPrevolver_1.STL_6  墙层数，增加桥接面积并优化悬垂。</li><li>用修改器将墙层数设为 1，并调整线宽，以增加桥接面积。</li><li>用负零件删除完全悬空部分，避免产生外墙缺陷。</li></ol>

A two-plate print of this dual-color model requires no AMS and is compatible with the A1 mini. Multiple overhangs and bridges prone to defects have been rectified. Supports have been redesigned to minimize unnecessary structures, facilitating easier removal. For overhangs with a base angle less than 45°, a gap greater than 0.2mm between the brim and the model is recommended for easier removal. Process parameters are suitable for both PLA and PETG. PETG HF is used by default; adjust the parameters to match your calibrated filament settings. Regardless of the model, it is always advisable to clean the build plate and apply a suitable adhesive before printing to prevent warping, detachment, and the formation of “spaghetti”.&nbsp;The following issues have been addressed:<ol><li>Increased wall thickness for TPrevolver_1.STL_6, expanding the bridge area and optimizing overhangs.</li><li>Employed a modifier to set the wall count to 1 and adjust the line width, enhancing bridge area coverage.</li><li>Utilized a negative part to remove completely unsupported sections, preventing external wall defects.</li></ol>

Two plates, dual color, no AMS required, A1 mini compatible.

user_3632179355

tempImagecqg3X7.jpg

For A1 Mini

单盘逐件打印的双色模型，需要 AMS。修复多处可能造成缺陷的悬垂和桥接。重新绘制支撑，减少不必要的支撑，更容易拆除。对于底面有 45°以下的悬垂，Brim 与模型的间隙应大于 0.2mm 便于拆除。工艺参数可用于 PLA 和 PETG。默认使用 PETG HF，请自行修改为你校准过的耗材参数。 无论什么模型，始终建议打印前清洁打印板并适当涂胶，避免模型翘边、脱离导致“炒面”。  &nbsp;修复问题如下：<ol><li>增加 TPrevolver_1.STL_6 墙层数，增加桥接面积并优化悬垂。</li><li>用修改器将墙层数设为 1，并调整线宽，以增加桥接面积。</li><li>用负零件删除完全悬空部分，避免产生外墙缺陷。</li></ol>

Single-plate, per-part printing of a dual-color model requiring the Bambu Lab AMSMultiple overhangs and bridges prone to defects have been rectifiedSupports have been redesigned to minimize unnecessary structures, facilitating easier removalFor base overhangs below 45°, a Brim clearance exceeding 0.2mm is recommended to ease removalProcess parameters are suitable for both PLA and PETG. PETG HF is the default; adjust to your calibrated filament settings. Regardless of the model, pre-print cleaning of the build plate with appropriate adhesive application is always advised to prevent warping, detachment, and subsequent stringing.&nbsp;The following issues have been addressed:<ol><li>Increased wall count for TPrevolver_1.STL_6 to expand the bridging area and optimize overhangs</li><li>Employed a modifier to set the wall count to 1 and adjusted line width to enhance the bridging area</li><li>Utilized negative geometry to remove entirely unsupported sections, preventing outer wall imperfections</li></ol>

Single plate dual color, fixes overhangs and bridges that may cause defects, optimized supports.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

<figure class="media"><oembed url="https://www.youtube.com/shorts/FYGPeo0pfSQ"></oembed></figure>This is a revolver that shoots six toothpicks, one press at a time.It uses a rotating drum mechanism that advances with each press of the trigger, aligning the next barrel in place. If you want to understand how the internal mechanism works, check out the video for the Q-tip version-<figure class="media"></figure>Recommended to print in PLA with good dimensional accuracy.

Print Profile(4)

Description

Comment & Rating (192)

License

Related Models

Toothpick Revolver

Print Profile(4)

Description

Comment & Rating (192)

License

Related Models