El1as

cover

20250427_153927.jpg

20250427_153701.jpg

20250427_153803.jpg

20250427_153942.jpg

20250427_153549.jpg

plate_1.png

2025-04-27_5dc2639b4866b.jpg

0.16 layer weight qualityDefault tree supportsInfill 15%GyroidRecommended print size: 20 cm height — just like shown in the photo for the best look and proportions.

0.16mm layer, 2 walls, 15% infill

domo326

IMG_9275(1).JPG

IMG_9273(1).JPG

IMG_9277(1).JPG

IMG_9278(1).JPG

Left all setting the same from original designer. Since its only 2 colors, the H2D prints this in a faster time.  It did ad some extra time because I did a smooth timelapse. Turn off timelapse and it will print in a faster time.

0.16mm layer, 2 walls, 15% infill H2D

ThePrinterPrinted

last+fixed+black.jpg

Slowed down first layer for better adhesion, removed words to minimize color changes.

25% Scale/No Words, 0.16mm layer, 2 walls, 15% infill

WeastBluePirate

IMG_0964.jpg

Changed up the writing on the hoodie.

I AM YOUR DADDY 0.16mm layer, 2 walls, 15% infill

zackza

photo_2025-06-07_07-42-53.jpg

photo_2025-06-07_07-42-57.jpg

photo_2025-06-07_07-42-50.jpg

photo_2025-06-07_07-42-46.jpg

This is @theprinterprinted ‘s 1.4 hour 25% scale , but scaled up slightly, with only 31 color changes, (only a few more than theprinterprinted &#39;s highly rated quick easy version but scaled up because in for a pound in for a penny, may as well scale it up and only add a few extra color changes!)&nbsp;It takes advantage of the low color changes from a blank shirt but scales it up slightly, and I think i should even post one more thats even larger. &nbsp;OH I also saved a LOT by removing unnecessary supports and the prime tower which is ALWAYS a big waste of time and filament unless you REALLy need precise colors, unnecessary here!&nbsp;GREAT Model i CANNOt wait to make more evebn larger profiles!

70mm 30%, no words, 0.16mm layer, 2 walls, 15% infill

photo_2025-06-07_19-07-29.jpg

photo_2025-06-07_19-07-34.jpg

photo_2025-06-07_19-07-42.jpg

photo_2025-06-07_19-07-53.jpg

photo_2025-06-07_19-08-00.jpg

45 color changes but under under 22 grams, only 8 grams flushed for color changes, 2 grams support, lol model only 11 grams BUT ITS WORTH it, the pile of waste is NOT THAT bad, and WILL be recycled and melted down into a silicon mold with a toaster oven one day, and theers other ways to compress filament waste with heat into bricks to use for stuff, so i do not mind. WORTH IT&nbsp;pictured is a 70mm version also from another profile. But i say, if youre going to print around 2 hours with 25 color changes you may as well do 45 and printf or 2 and a half hours! I guess I should just make even larger ones, OR I REALLy should make multiple at once right now hah BRB gonan print a plate!

90mm, 45%, 45 color changes, 0.16mm, 2 walls, 15% infill

KLINDON

IMG-20250505-WA0004.jpg

IMG-20250505-WA0005.jpg

IMG-20250505-WA0006.jpg

0,16 layer 2 lopp15% infilHo rallentato la velocita di stampa e degli spostamenti…poco piu lenta rispetto all&#39;originale un paio di ore in piu…Ottimo il risultato&nbsp;BUONA STAMPA A TUTTI

0.16mm layer height2 wall lines15% infillI reduced the printing and travel speeds slightly…a couple of hours longer than the original print time…Excellent result Happy printing everyone

Stampa rallentata TOP 0.16mm layer, 2 walls, 15% infill

3DPrintBeginner

I am your father4.png

I am your father1.png

I am your father2.png

I am your father3.png

Scaled up to 315mm - 0.16mm layer, 2 walls, 15% infill

plate_2.png

Kiki3D

1.jpg

2.jpg

3.jpg

4.jpg

5.jpg

Auf 600mm hochskaliert und mit einem H2D gedruckt Da der Slicer die Farben entfernt, sobald man ein Modell schneidet, habe ich diesen Darth Vader einfach halb “unter das Druckbett” geschoben. Ich habe vier Konnektoren hinzugefügt. Diese passten bei meinem Druck perfekt und ich konnte die beiden Teile zusammenstecken und kleben. Außerdem habe ich in den Füßen jeweils ein Loch hinzugefügt. Damit kann man das Modell z.B. auf eine Stange stellen, um ein Umfallen zu verhindern. Gedruckt mit Bambu PLA matt

Scaled up to 600mm and printed with an H2D Since the slicer removes the colors as soon as a model is sliced, I simply pushed this Darth Vader halfway "under the print bed" I added four connectors These fit perfectly with my print, and I was able to connect and glue the two parts together Additionally, I added a hole in each foot This allows the model to be placed on a rod, for example, to prevent it from toppling over Printed with Bambu PLA Matte

600mm height, 0.16mm layer, 3 walls, 10% infill, H2D

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

Urban-style Darth Vader statue, blending modern streetwear vibes with iconic Star Wars culture. Dressed in a hoodie with the famous quote &#34;I Am Your Father&#34; this sculpture brings a fresh, edgy twist to a legendary character. If you’re enjoying my 3D designs and want to help me create even more free, high-quality models, I&#39;d love it if you followed me and boosted my posts! 🚀✨ Every like, comment, and share really keeps me inspired to keep making and sharing with this awesome community. Thanks so much for he support!&nbsp;More urban models  coming soon!<commercialme><commercialtitle>Membership</commercialtitle></commercialme><boostme><boosttitle>Boost Me</boosttitle></boostme>&nbsp;

Darth Vader  I am your father, urban edition

ASIA

Print Profile(9)

Bill of Materials

Description

Comment & Rating (1066)

License

Related Models