Print-In-Place Motorhome RV - Free 3D Print Model

Search models, users, collections, and posts

Whopper Printing

Hobby & DIY>Vehicles

IP Report

Print Profile(3)

All

P1P

A1 mini

H2C

H2S

P2S

X1E

X1 Carbon

H2D Pro

P1S

H2D

X2D

A2L

0.2mm layer, 2 walls, 8% infill

Designer

2.7 h

1 plate

4.9(59)

Mini Version - 0.2mm layer, 2 walls, 8% infill

Designer

1.3 h

1 plate

4.9(28)

3 colors, 0.17mm layer, 2 walls, 8% infill, h2d

13 h

1 plate

Open in Bambu Studio

Boost

738

1474

250

139

2.4 k

1.6 k

Released

Description

Join my Patreon for more content and commercial license!

This model is fully print-in-place and does not require assembly. This is a great model to test your clearances, bed adhesion, and overhangs. The clearances are 0.3 mms on both models. If you'd like to see more of my designs, check my profile or click the Etsy link below for my paid models!

Please post your makes, I love seeing them!

Boost Me (for free)

Boost my model at no cost to support my work!

If you would like to support me, consider these options:

Social Links:

Comment & Rating (250)

@DigiPrint

The print profile is no longer public

Once it got done. I had to dam near break it to get the pop out to slide. Destroyed it enough trying to get it out. Don't even want it now as the slide out is ruined. Tried using a knife to clear anything in the cracks. STUPID. Wasted time and filament.

The profile uploader has replied

@BennyBoots

if plate hadn't fully cooled, it will stick to plate and deform the model trying to pry it from plate, causing the door to deform slightly and jam. perhaps your filament wasn't dry and it clumped at a spot internally around the door causing door to jam, or some other user error. you can see from other reviews, it prints fine.

(Edited)

@DigiPrint

Definitely was not user error. I am tech savy. Bed was clean. Filament was dry and not subject to extreme temperatures so there was no moisture in the roll. Also, this comment was posted elsewhere. So, not just user error when its a common problem.

@DigiPrint

Replying to @DigiPrint :

Just read through comments. Just so happen. The comment that said the same thing as mine. Is now gone...

@Distel3D

The print profile is no longer public

looks great love the pop out was a little hard to get the pop out though

@Red33

Boosted

how did you get yours to come out. can’t get it on mine

@Distel3D

Replying to @Red33 :

i used a blade and stuck it in then wiggled it around and it came out. i use the Bambu scraper blade

@Red33

Boosted

Replying to @Distel3D :

Thank you, got it out finally

@fansari

The print profile is no longer public

Another great model from this talented designer. Will look good in my motorhome! My only suggestion would be to redesign windows on the print bed side to avoid bridging. If they can be printed flat on the first layer they would look nice like the windows on the top side.

@Roboto88

Boosted

Print Profile

Mini Version - 0.2mm layer, 2 walls, 8% infill

Thanks for this:)

The profile uploader has replied

@WhopperPrinting

Looks great! Thanks for printing!

(Edited)

@Fardin11

nice🥳🥳

@SamStar

Anyone know why the wide extension won’t come out but the awning will? It may be from the infill but does anyone have any ideas of how to make it come out?