Anycubic Kobra S1 Combo ACE PRO Silica Gel Box - Free 3D Print Model

Search models, users, collections, and posts

CraftixDesign

3D Printer>3D Printer Accessories

IP Report

Print Profile(1)

All

Anycubic Chiron

0.2mm layer, 2 walls, 15% infill

Designer

6.4 h

1 plate

4.8(27)

Open in Bambu Studio

Boost

450

783

2.7 k

141

Released

Description

Content has been automatically translated.

Show original

Medium-Sized Silica Gel Box for the New Anycubic ACE PRO (with Filament Guide on the Lid)

Stable base due to wide footprint
Does not obstruct ACE LEDs
Easy removal
Accommodates two silica gel boxes and a temperature and humidity sensor in the center
Lid secured with two lugs

This box is freely available, but please remember that considerable time and effort were invested in creating this model A small tip would be greatly appreciated

PayPal.Me

Buy Me A Coffee

This is a medium-sized silica gel box, designed for the new Anycubic ACE PRO featuring integrated filament guides on the lid

Stable stand
ACE LEDs remain visible
Easy to remove
Space for temperature and humidity measurement in the center
Securely fastened lid

This design is free to use, but please keep in mind the considerable time and effort involved in its creation If you wish to express your gratitude, a small tip would be welcomed

Comment & Rating (56)

@user_2132869568

Thank you

Show original

@loksonick

Hey, the hygrometer holder is your design or you found it somewhere? Could you please share the link if possible? :)

@user_2132869568

Replying to @loksonick :

https://makerworld.com/pl/models/956087-thermometer-hygrometer-holder-for-ace-pro-41-5mm#profileId-925044

@CriArt3D

Thanks for the file I printed it in PETG Olive Green Translucent and it turned out very well

Show original

@pompeu_sbo

Could you send me the link to your filament guide for the Ace Pro?

@flar

Perfekt geworden

The designer has replied

@CraftixDesign

That makes me happy, many thanks for sharing the finished model! Best regards, Sascha

Show original

@AquaWide

clean impression and fits very well

Show original

@user_3300562699

Very nice model and fits perfectly

Show original

@user_930818129

I printed these out in Anycubic Orange PETG and they printed out perfect.

@togemini

How do you effectively remove the support structure, particularly from the ventilation slots

The designer has replied

Show original

@CraftixDesign

Hello, I did not use any supports at the ventilation slots, only at the bottom

Show original

@togemini

Replying to @CraftixDesign :

Thank you for your reply I'm still a newbie and the slicer added support to all four sides with the ventilation slots both inside and out I'll have to take a closer look at how best to remove the support The print itself was superb

Show original

@schnuffi09

In Anycubic Slicer, you must switch to "Tree Support (manual)". Then only the lower supports will be generated, omitting those within the slots

Show original

@Mahipster

Print Profile

0.2mm layer, 2 walls, 15% infill

@RoboticCrawdad

what model are you using for your temp/humidity sensor in the above picture?

@shean5911x

I found them on Aliexpress. 3 of them under 4$ Delivered, no idea how they are able to do that.

@RoboticCrawdad

Replying to @shean5911x :

I'm pretty i have the same ones. I meant which model did you for the mount they are in. Do you have a link? All the other ones I've seen look a bit too flimsy for my liking.

@jimlmackjr72

Replying to @RoboticCrawdad :

same question where the mouth for the sensor please

@Manni63

Print Profile

0.2mm layer, 2 walls, 15% infill

The lids are rather loose, perhaps a groove would be an improvement

Show original

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.