Keychain Siren Whistle - Free 3D Print Model

Search models, users, collections, and posts

WimV

Hobby & DIY>Other Hobby & DIY

IP Report

Print Profile(4)

All

P1S

A1 mini

H2D

X1 Carbon

P1P

X1E

H2D Pro

H2S

P2S

H2C

X2D

A2L

Whistle Complete One Color V2 (no sanding required)

Designer

27 min

1 plate

3.7(133)

Siren Whistle Complete - One Color (may require sanding!)

Designer

21 min

1 plate

3.9(45)

Siren Whistle Complete - Tri-Color (may require sanding!)

Designer

26 min

1 plate

3.9(12)

150% size, deeper pitch, 0.2mm layer, 2 walls, 15% infill

55 min

1 plate

4.5(18)

Open in Bambu Studio

Boost

709

1395

242

2.8 k

2.1 k

Released

Description

Easy and fast printing (only 6 gram).

Once you have printed, place the fan in the housing. Note the orientation: see image for the correct direction.

Click the lid into place and blow hard....

Adding a drop of oil to the shaft improves the friction on the fan and therefore gives much better performance!

Update 05-03:
Due to several feedbacks about stucking fan's, I reviewed the original printprofile and shared it as V2.
Because friction is a major factor for proper functioning I added ironing to all important surfaces.
I also decreased the hight of the fan by 0.2mm to allow a little more space between the fan and the lid.
(the original space between them was designed as 0.4mm what in some cases required sanding)
Please use at least a drop of lubricant to enhance the spinning even more. It may be any kind of oil…

* I fine-tuned the clamping of the lid by scaling the lid in X-Y. Adjust this in small increments of 0.2% if you find it clamping too hard or too soft.

(-0.2% for tighter clamping, +0.2% for lighter clamping)

* If the blade gets stuck (or does not rotate properly), lightly sand both sides of the blade on a flat surface. (only applies for original print profile's)

Comment & Rating (242)

@boongintnirp54

Boosted

Print Profile

Whistle Complete One Color V2 (no sanding required)

Love it. Was stuck at first but I was able to get it going with some greeese and extra persuasion. That "extra persuasion" was and air compresser😂, worked great to get it moving but be careful when doing that because if you go full force for an extended period of time you'll start to melt the fan or peg. Great Print. First engine whistle I'll be keeping for good.

@user_1935664660

And the intricate fingering?

Show original

@user_1935664660

Replying to @user_1935664660 :

and The sound?

@SkyLord

Print Profile

150% size, deeper pitch, 0.2mm layer, 2 walls, 15% infill

The model works well in itself, but when you mount the lid, the turbine is motionless. So that you can still use the pipe, you can only put the lid on the front

The profile uploader has replied

Show original

@gpb_45

I’m sorry, your problem is most likely due to tight tolerances. have you tried sanding the turbine or adding grease?

@SkyLord

Replying to @gpb_45 :

no I haven't tried it, but it would help with troubleshooting

Show original

@Raw7i

Boosted

Print Profile

Siren Whistle Complete - Tri-Color (may require sanding!)

i like how nice little its good for keychain,, its not the best sound maker there’s only other models make better sharp turbo like sound, maybe you can take that fan design shape and but it in your design to get better sound , but its great and i love it. for those who struggle blowing.. don’t install the cover fully because it hold the fan from spinning just give it a little space. and i always add a drop of oil in the center for good spinning only for once .

@Rowberry

could not get it To make a siren noise

@user_4270930512

Boosted

works like a charm! also in ABS.

@Irvs

Print Profile

Siren Whistle Complete - One Color (may require sanding!)

nice

@Raplof

Print Profile

Whistle Complete One Color V2 (no sanding required)

Prints well and works after a light sanding of the impeller

(Edited)

Show original

@user_4270930512

Boosted

Print Profile

Whistle Complete One Color V2 (no sanding required)

pretty cool design, used a bit of silicon lubricant to make it spin even better. I think I printed it in ABS (that roll was on the printer at that moment) and the noise is pretty annoying/fun

@bburch

Print Profile

Whistle Complete One Color V2 (no sanding required)

Great

@user_1278483578

Print Profile

Whistle Complete One Color V2 (no sanding required)

Amazing, but it did take a little before it started working

@user_636196017

Print Profile

Whistle Complete One Color V2 (no sanding required)

prited, failed, printed it again, assembly, didnt work, disassembly, sanding, assembly, still didnt work, trying both ways, still didnt work, sanded more, even the fan blades, still couldnt work

@NexNex2024

Try this one: https://makerworld.com/models/909879

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.