Bambulab A1 Mini Headshot / Poopshoot by halil_d

halil_d

3D Printer>3D Printer Parts

Print Profile(9)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 15% infill

Designer

30 min

1 plate

4.9(205)

0.2mm layer, 3 walls, 15% infill

Designer

1.8 h

1 plate

4.7(155)

0.2mm layer, 3 walls, 15% infill

Designer

1 h

1 plate

4.8(66)

0.2mm layer, 3 walls, 15% infill

Designer

1.5 h

1 plate

4.6(37)

Click to see more

Open in Bambu Studio

Boost

568

1060

626

2.5 k

2.6 k

Released

Description

15% Infill

Comment & Rating (626)

@Antassium

Print Profile

0.2mm layer, 3 walls, 15% infill

***EDITED REVIEW*** There are some fitment issues that cause rattling. Otherwise, this print worked well for me while I had it installed.

(Edited)

The designer has replied

@halil_d

So that the basket can be easily removed from the guide while the printer is running, the tolerances must be a little generous. The vibration can be easily remedied with a foam rubber pad

(Edited)

@Antassium

Replying to @halil_d :

Yes, the horizontal tolerances needed a small ammount, however, the verticle tolerances could be tighter, yet still allow it to slide in and out. That would reduce the rattle a lot. also, if the back of the basket was flat, you could rotate it on its back to print without supports. I will design a remix or a print profile soon to show what I mean.

@eornstein

Replying to @Antassium :

@halil_d everyone is a critic! I just got my mini in and started the print! awesome design thanks for sharing! @Antassium Might as well give your constructive criticism in the beginning, it will come off better and be a positive to the community reading and learning to design rather than saying "I can do it better" NEVER STOP LEARNING

(Edited)

@buschsim

I like the Idea. Thank you very much. But I suggest to make more use of 45 degree phases to make supports obsolete. Then e.g. frame could be printed on the back side. The used round edges look nice in CAD but they reduce print quality when used on top or bottom. Tolerance of the drawer is a bit high for me. drawer vibrates during prints. I think I will use some tape on the drawer to fix that.

(Edited)

The designer has replied

@halil_d

die toleranz musste ich so wählen da der auch während des druckens leichtgängig entnommen werden kann in der andere variante gab es beim entnehmen des korbs schwierigkeiten. die vibration habe ich jedoch nur am anfang bei der kalibrierung. hier könnte ein dünner streifen moosgummiband abhilfe schaffen.

@OgiArts

can you send me this model pls

@A_Bishop

Print Profile

0.2mm layer, 3 walls, 15% infill

came out great

@ferus.info

Looks great! I've added a missing frame profile for A1 Mini (could not load it in the app).

The designer has replied

@halil_d

Jo danke dir wurde wohl vergessen.👍

@vill.sigismondo

Boosted

Good model and good print with the profile connected, just a little difficult to remove the supports for some parts. Positive anyway!

@BillNyeTGG

Print Profile

0.2mm layer, 2 walls, 15% infill

fits and prints great thank you

@A_Bishop

One of the very first things I've Printed with my a 1 mini.

@A_Bishop

Print Profile

0.2mm layer, 2 walls, 15% infill

One of the first things I printed with my a one mini without any trouble

(Edited)

@Antassium

Print Profile

Mising A1 Profile for frame, 0.2mm layer, 3 walls, 15% infill

This part didn't print as well. the supports in the track left nubs that will be an issue when inserting the basket. It could be improved by changed the fillets on the backend for chamfers, then printing in a different orientation, with the back on the faceplate instead. I may remix this into a new profile at some point, but undoing fillets is tedious and time consuming without the original file...

@Antassium

Print Profile

0.2mm layer, 2 walls, 15% infill

Printed well and quickly. I didn't want multi-color on this part, so I just removed the other colors and printed black. I then added auto tree support and it worked fine. This fit well and will print the other pieces shortly.