A1 mini side box by LwFactory

LwFactory

3D Printer>3D Printer Accessories

Print Profile(4)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 15% infill

Designer

3.9 h

2 plates

4.7(118)

PETG!To prevent thermal deformation, and slightly increased the clearance.

Designer

4.8 h

2 plates

4.8(26)

Bambu Lab Logo NamePLate [PETG] 0.2mm layer, 2 walls, 15% infill

32 min

1 plate

5.0(13)

Drawer Insert for Nozzles/Tools

1.4 h

1 plate

4.8(5)

Boost

391

790

190

1.4 k

1.1 k

Released

Description

This is a tool box on the side of the A1 mini, perfectly fitting the 3D printer without interfering with the movement of the hot end and heated bed platform. It can be used to store tools such as wrenches, needles, and spare nozzles for easy access during regular use.

这是一个A1 mini侧边的工具盒，完美贴合3D打印机，并且不会影响到热端和热床平台的移动，可以用来放一些扳手、通针、备用喷头等物品，方便平时取用。你需要将

To install, you need to apply double-sided tape to the fixed block under the A1 mini's Z-axis guide, then push the tool box from the front until it sticks to the double-sided tape.
双面胶贴在A1 mini Z轴导轨下方的固定块上，再将工具盒从前方推入直至粘到双面胶上。

The decorative piece on the front of the tool box drawer can be switched with patterns according to your preference.

工具盒抽屉的前面的装饰件可以按你的喜好切换图案

Comment & Rating (190)

@VandalBee

I tried to make a remix of the model that works with: https://makerworld.com/en/models/104167#profileId-111236, but the mesh is a bit complex, and I cannot offset the faces. That model is like 12.5mm - would you be able to upload a new version that works with the model above?

(Edited)

@user_48729073

Add a negative cube component and place it here to cut off a portion

@ChrisDoubleL

Print Profile

0.2mm layer, 2 walls, 15% infill

Fantastic drawer, fits perfectly, look great and is very useful. Thanks. WARNING as the drawer is placed so close to the heatbed it means it can warp, see my comment below, if I can't salvage it I will print again in PETG abd hope that holds up better, I will leave at 5* for now as the object itself is fantastic.

(Edited)

The designer has replied

@ChrisDoubleL

Unfortunately this has now warped and the drawer is almost impossible to remove, probably because of quite a few long petg prints. I would suggest printing this in petg, I will try to salvage by sanding the inside drawer but if not I will print again in petg as it is a nice addition

@ChrisDoubleL

Printed replacement housing in PETG, which sits perfect. The PLA drawer is a bit tight but right now it's the perfect amount as it will stop any movement while printing. Hopefully this combination will stand up to the heat, will update if anything changes

@LwFactory

Thank you very much for your reminder. I am also validating the PETG version. If it works effectively, I will upload the PETG slicing configuration and adjust the tolerance range to address any potential minor deformations.

@marcle

Print Profile

0.2mm layer, 2 walls, 15% infill

Nice job. I recommend not printing it in white because you will get reflections from the camera light.

@user_1717369054

我打印成型粘在机器上，一周后，抽屉侧面的小抽屉就因为收缩打不开了。。。

@user_1717369054

问题不全在小抽屉的侧面，是底层收缩了，把抽屉整体卡住了。。。太难了

@user_1870308925

Tried printing in PETG, this was the result :| will try again, any advice?

@user_2305579096

you use the wrong direction, you should not use Z instead of Y or X

@GasKB

Print Profile

PETG!To prevent thermal deformation, and slightly increased the clearance.

Everything perfect!

@thibaud

Very perfect ! PLA white Elegoo and Kaki Wanhao

(Edited)

@Keppo87

Print Profile

0.2mm layer, 2 walls, 15% infill

perfetto utile e molto ordinato.. consiglio però di aggiungere un piccolo distanziale in modo che il calore venga dissipato in quanto la parte sottostante scalda molto!

@pincombe

Print Profile

PETG!To prevent thermal deformation, and slightly increased the clearance.

Printed out really well. I originally printed in PLA and unfortunately the whole thing warped after a week and I couldn't open the drawer. Ended up having to put it in the oven for a few minutes to get the stuff out and then reprinted a new drawer in PETG.

@Misterx31

Ich habe diese sehr praktische Toolbox in weiß/grau Sunlu High Speed PLA ausgedruckt. Endlich bekomme ich mein ganzes Werkzeug platzsparend unter ;) Vielen Dank für super Idee ! I printed this very practical toolbox in white/gray Sunlu High Speed PLA. I can finally fit all my tools in a space-saving way ;) Thank you for a great idea!

(Edited)