EZ AMS Helper
Copyright Claim
EZ AMS Helper
Boost
277
593
271
Print Profile(5)
4 Pieces 0.2mm layer, 2 walls, 15% infill
Designer
17 min
1 plate
Larger AMS Feeder Port, 0.2mm layer, 2 walls, 15% infill
Designer
17 min
1 plate
0.2mm layer, 2 walls, 15% infill
Designer
11 min
1 plate
0.16mm layer, 3 walls, 15% infill
32 min
1 plate
Click to see more
Open in Bambu Studio
Boost
277
593
271
24
1.8 k
1.2 k
Released
Description
Simple and easy AMS Helper System. The design attachs directly to the first stage feeders filament intake.
Before you print:
- I´ve got feedback, that the size of the first stage feeder port varrys. If you have the larger Port than you should use the print profile for the larger one. (Larger means 3,1mm in height instead of 3mm)
Advantages (i have noticed):
- No wear out of the grey filament intake port of the first stage feeder
- Fixed filament retraction problem where the filament gets all over the AMS
- Reduced horizontal stress on the first stage feeder
- Fixed spool hopping when filament gets low
Assembly:
- Just stick a PTFE tube into the clip and slide it on the first stage feeder.
- Optional put a bit of glue in the hole before sticking the ptfe tube in to prevent slipping out
Notes:
- I use 9cm long PTFE tubes. Maybe the optimal length is different… (Update 18.2: Trying 9cm tubes instead of 13 cm)
- This helper should also work with the Hydra AMS System
- Check also out my PTFE Tube Protector: https://makerworld.com/en/models/234268
Installation on the AMS:
- Here you can see how to install the EZ AMS Helper on the AMS. Just slide it on, don´t try to mount it from the top.
Comment & Rating (271)
All
holds perfectly even without a hose, the filament runs cleanly through the AMS
The designer has replied
2
Reply
I like the idea...so it´s even more easy :-)
1
Reply
Replying to @MakerJoe
as a suggestion for improvement:
Could you add a bevel to the hole so that the filament doesn't drag on the edge of the hole.
0
Reply
Replying to @Marco_94
Great idea, i will do that and let you know :)
1
Reply
Print Profile
4 Pieces 0.2mm layer, 2 walls, 15% infill
printed great, but does not fit on my version (new) AMS. It may just be tolerance of my printer and not necessarily a fault of the model.
The designer has replied
1
Reply
It fits very tight to ensure it does not slip off. My AMS is two months old...
Please let me know if i can support u
(Edited)0
Reply
Replying to @MakerJoe
I will try again if I get an error, but as I said, it may just be my print tolerance.. as I didn't want to force it and break anything fitting them...
0
Reply
Replying to @atlixanet
I´ve enhanced the models description with an installation video. Nevertheless, maybe you can give me the exact measures of your ams first stage feeders port. I would like to understand why it´s not fitting. I tried it with a brand new one...
0
Reply
Print Profile
4 Pieces 0.2mm layer, 2 walls, 15% infill
have two that would not go on and has to trim inside but the rest went on great just need to test if I get any issues with these
The designer has replied
1
Reply
Thanks a lot for your review. We´ve discovered that there are some tollerances with the first stage feeders intake height
0
Reply
yeah was weird two fit fine but the other two I really struggled with
0
Reply
Print Profile
4 Pieces 0.2mm layer, 2 walls, 15% infill
Works!
The designer has replied
2
Reply
Thanks for your review :)
0
Reply
I tried this with ABS, PLA and PETG - all models broke directly. Maybe I get something wrong but for me it doesn’t work at all.
The designer has replied
0
Reply
Thats strange...have you tried the larger print profile? Maybe your feeder port is one of the bigger ones
1
Reply
Replying to @MakerJoe
Just scaled it to 103% - now works like a charm. I updated my rating to five stars 🤩
1
Reply
Boosted
Print Profile
4 Pieces 0.2mm layer, 2 walls, 15% infill
used translucent green petg inland
The designer has replied
1
Reply
Looks great :)
0
Reply
Print Profile
4 Pieces 0.2mm layer, 2 walls, 15% infill
passen gut
The designer has replied
1
Reply
Klasse, das freut mich 👍danke für deine Bewertung
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
works great thanks 👍
The designer has replied
1
Reply
Thanks a lot for sharing
0
Reply
nice job!
The designer has replied
1
Reply
Thanks for sharing. Nice transparent tubes :-)
0
Reply
Print Profile
4 Pieces 0.2mm layer, 2 walls, 15% infill
Came out great! Thank you!
The designer has replied
1
Reply
Thanks for sharing and rating :)
0
Reply
License
This user content is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Related Models
© 2024 MakerWorld