Sleek Passport Case

Copyright Claim

Sleek Passport Case

Boost
2090
4394
257

Print Profile(8)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

0.2mm layer, 3 walls, 25% infill
0.2mm layer, 3 walls, 25% infill
Designer
1.9 h
1 plate
4.9(109)

A1 Mini - 0.2mm layer, 3 walls, 25% infill
A1 Mini - 0.2mm layer, 3 walls, 25% infill
Designer
2.3 h
2 plates
4.9(30)

Larger - 0.2mm layer, 3 walls, 25% infill
Larger - 0.2mm layer, 3 walls, 25% infill
Designer
2 h
1 plate
5.0(27)

2 Passports - 0.2mm layer, 3 walls, 25% infill
2 Passports - 0.2mm layer, 3 walls, 25% infill
Designer
2 h
1 plate
4.9(19)
Click to see more

Open in Bambu Studio
Boost
2090
4394
257
226
2.9 k
1.7 k
Released

Description

Using feedback from the Slim Passport Case, this new passport case was designed to improve printing consistency and reduce errors.

Enhancements over Slim Passport Case: 

  • Thicker & overlapping edges for less warping and sturdier build
  • Locking nubs on ends to keep case closed on all sides - no more edges coming up
  • Redesigned hinge - smaller, lighter, and reduced breaking while folding after print
  • Stiffer pocket spring
  • A1 mini profile included

 

Octagram spiral top and bottom by default. Some filaments don't like this, so print slow and hot for the first layer if using PLA silk or PETG. 

 

Perfectly fits a passport with a pocket to hold other important documents like IDs, immunization cards, etc. Looks great with effect sheets.

Print in place other than the pocket that snugly slides into place. 

 

Let the case cool completely before removing from build plate. 
 

Comment & Rating (257)

Please fill in your opinion
(0/5000)

Unfortunately, it doesn't stay closed… printing in PETG
The designer has replied
Show original
0
Reply
What is keeping it from closing properly? Is the passport too thick?
0
Reply
Replying to @wetplaguru :
it’s like that
0
Reply
looks warped. does the case lay flat still when opened?
0
Reply
Print Profile
A1 Mini - 0.2mm layer, 3 walls, 25% infill
Wow...
2
Reply
This filament is beautiful! What filament is this??
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 25% infill
excellent print, although would be nice to see a radius on the ticket holder to match the inside so it sits flush at the bottom? or am i being too picky lol, 5 stars either way :)
The designer has replied
0
Reply
@D6CXY I did try something like that but with the way the insert prints vertically it's hard to get those nice fillets on the bottom of the print.
2
Reply
Replying to @wetplaguru :
Someday 3D printers will print bed-facing fillets. Today is not that day. Thanks for sharing. Very stylish.
0
Reply
Boosted
Replying to @wetplaguru :
fair enough! thanks for the reply
0
Reply
Print Profile
0.2mm layer, 3 walls, 25% infill
i scaled it 5% to compensate for the passport protector, work nice
3
Reply
Print Profile
A1 Mini - 0.2mm layer, 3 walls, 25% infill
Very much appreciate the design, but the a1 mini design doesn't work. The two pieces fall apart every time I open the wallet. Does the version on bigger printers have a tighter hinge?
The designer has replied
0
Reply
Sorry you’re having that problem. Are the hinges binding and bring pried apart? I’ve seen that happen before. I just worked the hinge back and forth to smooth them out. The other versions have a completely closed hinge that can’t come apart.
0
Reply
Replying to @wetplaguru :
No worries, i understand the time it takes to work on designs and appreciate the upload, The issue i'm having is it seems the hinge is too loose, it quite easily separates at the hinge when you open it
0
Reply
Print Profile
0.2mm layer, 3 walls, 25% infill
Beautiful!
1
Reply
Print Profile
0.2mm layer, 3 walls, 25% infill
great !
1
Reply
Print Profile
0.2mm layer, 3 walls, 25% infill
I can get it to close right as many of the other comments say
The designer has replied
0
Reply
Could you provide a photo of where it’s not closing right?
0
Reply
Replying to @wetplaguru :
I thought at first it was just some warping, but then I went through and checked all the comments and realized everyone else was having a similar if not the same problem that is with the passport out of it as well with the passport in it doesn’t close very well
0
Reply
@Stone10 Thanks for the photo! Did you let it cool before you took it off the plate? What plate/filament and I can re-create it. Any custom settings?
0
Reply
Boosted
Print Profile
0.2mm layer, 3 walls, 25% infill
this is an awesome print, thank you,
1
Reply
Boosted
Print Profile
2 Passports - 0.2mm layer, 3 walls, 25% infill
added some flags and also printed some personalised ones with names on them, turned out awesome thanks.
1
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.