Ikea Samla 22l Clip - Never Lost by Generics

Generics

Hobby & DIY>Other Hobby & DIY

Print Profile(4)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 3 walls, 15% infill

Designer

32 min

1 plate

4.9(35)

[PLA] 8 SAMLA (22L) clips on one plate

2.5 h

1 plate

5.0(4)

[PLA] 16 SAMLA (22L) clips on one plate

4.8 h

1 plate

5.0(1)

[PLA] 24 SAMLA (22L) clips on one plate

7.2 h

1 plate

5.0(1)

Open in Bambu Studio

Boost

125

218

247

Released

Description

Summary

Another simple Clip for your 22l Samla Box with or without sealing. Just a satisfying “Click” and closed.

Use a strip of double-sided adhesive tape (showcase on the pictures - red stripe) and you are done with searching your Samla Clips.

I used this one: https://www.amazon.de/gp/product/B008KJDY0G?th=1

Don't be afraid, you need some force for the first movement.

Motivation

I tried a lot of clips, some are good with, some without sealing. Some of them are popping around and others… You probably know what I mean. At least, all of them must be removed, put aside and then mounted again. Annoying...

How to print

Multipble prints at the same time are possible. Best results with only 1 per print.

Filament: PETG is working fine

Nozzle: 0.4mm
Height: 0.2mm
Supports: NO!
Perimeters: 3
Infill: 15-20%
Brim: Nope

Comment & Rating (48)

@ShayneTroxler

Boosted

Printed a half dozen in ABS as I have not had good luck with petg or pla that is under stress. I've left a reminder to check back in 90 days to see how they are fairing. I'll be sure to let you know! Thanks for the design!

@ShayneTroxler

Boosted

I'm checking back to report they are still working fine. I'm glad I printed them in ABS, I've had a spate of functional PLA and PETG prints fail. This is a great clip and the print in ABS was spot on.

@Kumpelblase

Print Profile

[PLA] 8 SAMLA (22L) clips on one plate

The best clip I printed so far. Works great!

@bellonius

Print Profile

0.2mm layer, 3 walls, 15% infill

Printed flawlessly in PLA. Good strong feeling hinges and clip tightly onto Samla.

@Hinti

Boosted

Thanks! Perfect pass. I used PETG. 3 walls. Wall Arachne. 20% fill - for stability "Archimedean Chords" with unlimited anchor length/max.

@average3D

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill

another great never lost ikea SAMLA clip! at first I printed a single one to check tolerances and then printed 24 clips on one plate. no noticeable difference! works great as intended and very boost-worthy! ❤️

@PTejada

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill

great print. Use "Prin sequence - By object" to print all 8 on one plate.

@Kawa

Print Profile

0.2mm layer, 3 walls, 15% infill

Works perfect - thank you!

@nixionus

Boosted

Print Profile

0.2mm layer, 3 walls, 15% infill

Force needed is optimal for 2mm isolator. Very good

@DMTGDesign

Print Profile

0.2mm layer, 3 walls, 15% infill

Wow ! Tried with one piece to be sure, it goes perfectly with PLA ! Now let's print a little batch of it... Thx a lot for this model !

@furkan1

Print Profile

0.2mm layer, 3 walls, 15% infill

when i printed 8 pieces on one plate, it came out like in the first photo, but when i printed just one piece on one plate, it was better and usable but still not perfect

(Edited)