BambuLab X1 internal waste cleaner by JeanJean3d

JeanJean3d

3D Printer>3D Printer Accessories

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

0.16mm layer, 2 walls, 15% infill

Designer

54 min

1 plate

4.5(22)

0.2mm layer, 2 walls, 10% infill

Designer

47 min

1 plate

5.0(3)

0.2mm layer, 2 walls, 15% infill

Designer

48 min

1 plate

4.3(4)

Open in Bambu Studio

Boost

164

253

169

Released

Description

A fast and easy to print internal waste cleaner for your BambuLab X1 / X1c.
I printed it in 45 minutes and it used 35gr of PLA.
You can leave it in the printer during your prints, in front of your print bed.
Can be resized if you want to use it in a other printer.

PS: i uploaded 2 new versions, a little more larger (315mm) and it fit perfectly in my X1, see this link:

https://makerworld.com/en/models/103521

Don't forget to rate my prints :)

Comment & Rating (38)

@MadeIn3Dxyz

Print Profile

0.16mm layer, 2 walls, 15% infill

Very useful.

@FeliciaFelicis

Print Profile

0.16mm layer, 2 walls, 15% infill

attempted to print this w generic petg, resulted in failure. filament warped/broke after extrusion and began flaking off. I'll try again w some other filament eventually and relate, but for now I'm moving on.

The designer has replied

@JeanJean3d

Hello. I'm sorry to read that you had problems to print this model. I printed it in Bambulab PLA and Bambulab PETG, without any problem. Both are just great ... Did you use my print profile? Are there enough walls? Please, can you try it in PLA? I'm sure it will print it like it should. Let me know. Best regards Jean

@schmi_mi

Print Profile

0.16mm layer, 2 walls, 15% infill

sorry, I first used it in a wrong way. Now I know how to use it and it works great

(Edited)

The designer has replied

@JeanJean3d

Hello. Thanks for your rating, but why only 4 stars? Did you have a problem with this print? Thanks Jean

(Edited)

@Infantryman

Nothing is better than a vacuum!

The designer has replied

@JeanJean3d

Yes, i agree, but if you don't have one by hand ... :)

@TheGryzz

Print Profile

0.16mm layer, 2 walls, 15% infill

Great design, simple print. Thanks!!!

The designer has replied

@JeanJean3d

thanks to you, that you downloaded, printed and commented :)

@MozerMade

Print Profile

0.16mm layer, 2 walls, 15% infill

works

@jethro42

Print Profile

0.16mm layer, 2 walls, 15% infill

Was hard to get to stick using PETG on my build plate but it does work, I did end up just using a brush instead though.

@3DPrintsBF

Print Profile

0.2mm layer, 2 walls, 15% infill

awesome 👍🏻 works great

@brightenw8

Print Profile

0.16mm layer, 2 walls, 15% infill

it’s simple but works

@seranuxue

Print Profile

0.16mm layer, 2 walls, 15% infill

The designer has replied

@JeanJean3d

Hello. Thanks for your rating, but why did you select 2 stars and don't write why you give only 2 stars ??? Hope to read you soon. Best regards Jean

@seranuxue

Replying to @JeanJean3d :

Me hubiese gustado que ajustase bien en longitud. Y el hueco que tiene en medio seria mejor rellenarlo para poder sacar todo el material. A mi parecer...

@JeanJean3d

Replying to @seranuxue :

Google translate from spanish: I would have liked it to fit well in length. And the gap in the middle would be better filled to be able to remove all the material. In my opinion My answer: i will rethink my design, possible that you're right, everything can be better, just have to think about it :) Thanks