(Metric) Ultimate T-Handle Hex Key Set
Remixed by
Copyright Claim
(Metric) Ultimate T-Handle Hex Key Set
Remixed by
Boost
131
256
56
Print Profile(2)
0.16mm layer, 4 walls, 25% infill
Designer
60 h
31 plates
0.2mm layer, 3 walls, 25% infill
22.7 h
18 plates
Boost
131
256
56
12
437
455
Released
Description
Update 2024-01-03: Added 5.5mm versions (big handle)
Update 2024-01-02: Added 1.25mm, 3.5mm and 4.5mm versions (small handle)
After a lot of work, here is my Ultimate T-Handle Hex Key set, designed in 9 common sizes (1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm and 10mm)
- SAE version is available here : https://makerworld.com/en/models/81110
- Torx version is available here : https://makerworld.com/en/models/239133
- Stand available here : https://makerworld.com/en/models/78304
Print in place, no glue required, handles knurling gives a nice feeling in the hand.
It's made to be tight, to avoid the key to move, it should be easy to assemble, but if it is a little hard to screw (example with coated keys, which is a little bigger), a drop of grease or oil on the thread could help.
There is 2 handle sizes : One small for allen key from 1.5mm to 4mm and a large for 5mm to 10mm
Give your feedback and post your makes, enjoy!
PS : Feel free to ask other sizes
Comment & Rating (56)
All
Print Profile
0.16mm layer, 4 walls, 25% infill
These work great. Printed with no mods and the fit the allen keys very well. Would like to know if you would be able to do a 1.27, 3.5, 4.5 and 5.5 to finish off my full set of wrenches. :)
The designer has replied
0
Reply
Sure, no problem, I made a parametric model so I can make any size easily, but I do not have those sizes, so I can't test. would you be a beta tester to confirm it fits well ? 😉
0
Reply
Replying to @MarcelBichon
Absolutely. I am a great tester, love to tinker.
0
Reply
Replying to @eaputt
Hi, I just added 1.27, 3.5 and 4.5mm sizes, raw files and print profile, confirm all is ok!
0
Reply
Print Profile
0.16mm layer, 4 walls, 25% infill
love the way they look! makes my basic Alen keys look fancy! Very Strong Print was able to use them to built a monitor arm, tighten all the screws on the arms!
(Edited)
The designer has replied
1
Reply
Realy great! Was the fit with allen keys correct ?
0
Reply
Yes it was! the smaller Alen keys were a bit difficult to get thru the bottom cap, but once I did, it wasn’t bad!
0
Reply
Print Profile
0.16mm layer, 4 walls, 25% infill
Absolutely love the design. Print was perfect. Snug fit that required some grinding to line up the numbers perfect.
As you have a parametric design, have you ever thought of making a version for Torx? I‘d love to have one for my T10 - T50 set.
Thank you.
The designer has replied
0
Reply
I have no torx set so I can't measure, however I think, unless allen keys, all the brand are not the same size ?
0
Reply
Replying to @MarcelBichon
I don’t know, if there are standardized dimensions. I have the set from S&R and the key have the following dimensions:
T10 - 3mm
T15 - 3,5 mm
T20 - 4mm
T25 - 4,5mm
T30 - 6mm
T40 - 7mm
T45 - 8mm
T50 - 9mm
It would be great if you can add the models for those.
0
Reply
Replying to @Thjorim
could you test if it works with the corresponding allen handles ? ex: does the T20 works with the 4mm handle ?
0
Reply
Print Profile
0.16mm layer, 4 walls, 25% infill
Snug fit, love the layout of the plates, printed the handles all one color just for a quicker print, and had the number be a different color.
The designer has replied
0
Reply
great in one color too, must save a lot of time!
0
Reply
Printed nice - Used ASA I had on hand. Did have a little warping issue - tolerances were perfect.
0
Reply
Print Profile
0.16mm layer, 4 walls, 25% infill
very nice.
0
Reply
Print Profile
0.16mm layer, 4 walls, 25% infill
perfect!! just what I needed!
0
Reply
Eine wirklich sehr gute Idee. und es funktioniert perfekt einfach tropfen öl dran und zusammen schrauben
0
Reply
Boosted
Print Profile
0.16mm layer, 4 walls, 25% infill
0
Reply
Print Profile
0.16mm layer, 4 walls, 25% infill
found i had to scale up all the outer parts to 102% as they wouldnt screw on at normal scale, they were too tight
The designer has replied
0
Reply
Hi, did you print in PLA ? also, is it too tight with or without the allen key in place ? And is the alen key secured (doesn't move) with caps at 102% ? Thanks for your feedback ;)
0
Reply
Replying to @MarcelBichon
was too tight with the allen key in place. 102% they are nice and snug and the key doesnt move
0
Reply
This remix is based on
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRemixes (2)
© 2024 MakerWorld