AMS Fidget Toy Keyring by BuildyBryce

BuildyBryce

Toys & Games>Puzzles

Print Profile(2)

All

X1 Carbon

P1S

P1P

X1E

A1 mini

Multicolour (0.16mm layer, 2 walls, 15% infill)

Designer

1.6 h

1 plate

4.1(9)

Multicolour for A1 Mini (0.16mm layer, 2 walls, 15% infill)

Designer

1.9 h

2 plates

5.0(1)

Boost

104

Released

Description

A fidget toy keyring designed to resemble the Bambu Lab AMS.

This version is smaller than my fullsize version, and features a loop for adding it to your keys/lanyard/whatever!

Each filament spool ratchets and makes a satisfying sound when spun!

Try Out My Other Fidget Toys!

Assembly Instructions

Step 1: Cut a 45mm length of 1.75mm filament.

Step 2: Attach the lid and base of the AMS together using the 45mm filament as a hinge.

If the filament doesn't fit, ensure there is no support material in the hinge. If it still doesn't fit, adjust your print settings and try again (or use a drill/lighter).

Step 3: Assemble the 4 filament spools.

The 2 halves should snap together firmly without glue.

Step 4: Put the spools into the AMS and use the square bar to lock them into place.
You might also want to glue the bar into place by adding a tiny amount of glue on the sides.

Step 5: You're done!

If the filament spools don't rotate properly. Ensure that the ratchet piece is facing the correct direction, or flip the spools around.

Comment & Rating (11)

@Claw501

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

Printed perfectly except that the bottom of the lid was filled in and so the hinge is only attached to one side.

(Edited)

@Yuro3d

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

I had a few issues with the print profile, had to change the supports to tree and build plate only, default has normal and fills in/blocks the holes on the hinge where the filamentstrip goes through, also bar that the spools sit on was a little big changed the y and z to 98 left the x at 100 and worked perfectly.

@user_2471965059

how does it open if the file is shows it is closed

@user_1806697876

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

seht sehr cool aus. Es geht etwa 7 Minuten um das Mini AMS zusammen zubauen

@pawprintz3d

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

Printed easily and super fun to play with.

@iamweird

Boosted

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

Support Issue:supports are way too hard to remove, you should use tree

@Voltz18

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

Support Issue

@Shilo

Print Profile

Multicolour for A1 Mini (0.16mm layer, 2 walls, 15% infill)

@Stokalic

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

@warmup

Print Profile

Multicolour (0.16mm layer, 2 walls, 15% infill)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.