Filament Buffer Spool Side PTFE Guide

Filament Buffer Spool Side PTFE Guide

Boost
76
184
99

Print Profile(3)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

PETG 0.2mm layer, 6 walls, 25% gyroid infill
PETG 0.2mm layer, 6 walls, 25% gyroid infill
Designer
32 min
1 plate
5.0(41)

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
23 min
1 plate
4.9(7)

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
32 min
1 plate
5.0(1)

Boost
76
184
99
2
429
220
Released

Description

Buffer Spool-Side PTFE Guide

This simple guide helps to keep your PTFE tube aligned and secure. This is the last leg of PTFE tube before entering the chamber. If your filament got this far keep it on track to get the job done.

 

Simple print using very little filament. I consider it a must have item to reduce the opportunity for a print failure due to some feed or pull back issue.

 

NOTES:

  • This version requires the stock spool arm for installation. If you have remove the stock spool arm check out my other version.
  • By design the guide for the PTFE tube is oversized to accommodate the movement of the PTFE tubes movement from the Filament Buffer.
  • See Installation notes below

CLICK HERE TO CHECK OUT THESE OTHER PTFE ACCESSORIES

INSTALLATION;

  • Remove the PTFE tube from the PTFE connector at the top of the printer
  • Remove the stock spool arm
  • Install the Buffer Spool-Side PTFE Guide in the spool arm as seen in the photos
  • Route the PTFE tube through the guide
  • Reinstall the spool arm
  • That's it!

 

Comment & Rating (99)

Please fill in your opinion
(0/5000)

Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
It was very intelligent of you to take advantage of the filament spool holder. Well done, and thank you for the make!
(Edited)
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
Very nice, everything worked great.
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
imprimé en abs merci pour le modèle il fonctionne très bien
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
Printed and working well!
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Boosted
Simple and clever design. Perfect.
The designer has replied
1
Reply
Thank you for the feedback! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
top
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
The PTFE guide is a very nice addon for my p1s
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other models and Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Works great! I have a P1S and it is a tight fit for the plug. It appears that your plug is slightly lower
The designer has replied
1
Reply
Glad to hear it fits and is working great for you.
0
Reply
Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
Works great
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply
Print Profile
PETG 0.2mm layer, 6 walls, 25% gyroid infill
Came out perfectly.
The designer has replied
1
Reply
Thank you for the feedback and 5 star rating! Make sure to check out my other Bambu Printer Accessories. More to come so LIKE and FOLLOW to get updates. Thanks again!
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.