Bambu Pull Tray Purge Bucket by Urban 3D

Urban 3D

3D Printer>3D Printer Accessories

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

0.2mm layer, 3 walls, 15% infill

Designer

13.8 h

2 plates

4.4(36)

0.2mm layer, 3 walls, 15% infill

Designer

23.4 h

2 plates

4.5(8)

SUPERFAST 0.24mm layer, 3 walls, 15% infill correct position and brim

12.5 h

2 plates

3.0(1)

Open in Bambu Studio

Boost

207

380

1 k

418

Released

Description

The updated version of this file can be found at Bambu Pull Tray Purge Bucket UPDATED by Urban 3D - MakerWorld and is the one i reccomend printing as it is just much better!

This purge bucket features a tray that is easily pulled out to empty the waste. I have also attached the .step and fusion file for easy remixing.

Comment & Rating (63)

@samara8609

when it purges it seems to only make it to the ramp and not down to the bucket

The designer has replied

@sajungzak

This

@zryder94

It seems as if the ramp needs to be steeper.

@Urban3D

Replying to @zryder94 :

https://makerworld.com/en/models/82533#profileId-87983 check out this version that features a steeper ramp, LESS material to print, and has slots for two 3x9 magnets!

@IkesCreations

Print Profile

0.2mm layer, 3 walls, 15% infill

works great!

(Edited)

The designer has replied

@Urban3D

Looks great!

@southern_prints

Print Profile

SUPERFAST 0.24mm layer, 3 walls, 15% infill correct position and brim

fits and looks very nicely, but ramp is t steep enough so poop gets stuck on it and actual bucket is slightly taller than end of ramp

(Edited)

@Wells.6605

solid black. looks sharp. printed great.

@schneewittchen

Print Profile

0.2mm layer, 3 walls, 15% infill

fits perfectly with an Ikea Metod cabinet and the insulation. Thanks to the bin, I've solved the problem of where the garbage ends up.

@Wells.6605

Print Profile

0.2mm layer, 3 walls, 15% infill

printed great. however I had a slight edge curl that I didn't miss. now the inside box sits 3/16 above the lip of the shoot. Why not make the box 1mm or .5mm shorter just in case this happens. I now have to either reprint the entire outside shell, or hand cut the inside box. just a thought. but over all heat print. thanks.

@white92k

Print Profile

0.2mm layer, 3 walls, 15% infill

it catches the excess material, but it dosent send it to the bucket, they just sit on the slide. maybe the angle is not sloped enough. but i still enjoy using it haha

The designer has replied

@zryder94

I have the same issue, it seems as if the ramp needs to be steeper.

@Urban3D

Replying to @zryder94 :

https://makerworld.com/en/models/82533#profileId-87983 check out this version that features a steeper ramp, LESS material to print, and has slots for two 3x9 magnets!

(Edited)

@Shifty

Cool idea, but the ramp is not steep enough. my chute backs up after a few hours of a multicolor print.

The designer has replied

@Urban3D

I will work on it as soon as I have some free time

@Shifty

Replying to @Urban3D :

Awesome to hear! I love the concept overall!

@Urban3D

Replying to @Shifty :

https://makerworld.com/en/models/82533#profileId-87983 check out this version that features a steeper ramp, LESS material to print, and has slots for two 3x9 magnets!