mini airplane 3.0

mini airplane 3.0

Boost
161
273
105

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
A1 mini

0.08mm layer, 2 walls, 80% infill
0.08mm layer, 2 walls, 80% infill
Designer
23 min
1 plate
4.7(49)

0.12mm layer, 2 walls, 80% infill
0.12mm layer, 2 walls, 80% infill
Designer
18 min
1 plate
3.7(3)

0.08mm layer, 2 walls, 80% infill, A1 mini
0.08mm layer, 2 walls, 80% infill, A1 mini
26 min
1 plate
3.8(18)

Open in Bambu Studio
Boost
161
273
105
20
653
623
Released

Description

EDIT:

The wings must be printed on 3 layers, otherwise the plane does not fly well. please check this out in BAMBU studio

The Airplane is printed upside down, after printing the model must be turned and the wings bent in the right direction

 

another version of the mini plane. the first layer must have a height of 0.12, for greater strength. other layers are set to 0.08mm. Bend the rear wings under approx. 45°. The large wings can also be bent. Throw the glider up, then it flies far, suitable for years of use even into the wind. I also added another print profile with all layers 0.12mm, but it's not as good

 

Comment & Rating (105)

Please fill in your opinion
(0/5000)

Print Profile
0.08mm layer, 2 walls, 80% infill
beautiful
The designer has replied
1
Reply
thank you ☺️
0
Reply
I had to set first layer to 0.119 to get 3 layers on the wings. works great! really zips! Printed with a 3 color silk.
The designer has replied
1
Reply
nice, only the wings are upside down, the print is upside down
0
Reply
Print Profile
0.12mm layer, 2 walls, 80% infill
It don't fly really good
The designer has replied
1
Reply
this profile is not very good, the best is with a layer height of 0.08 mm
0
Reply
Print Profile
0.08mm layer, 2 walls, 80% infill
Printed out nicely and a very quick print
The designer has replied
1
Reply
thank you :)
0
Reply
Print Profile
0.12mm layer, 2 walls, 80% infill
It kinda works but with a little less weight i think it can fully fly
The designer has replied
1
Reply
thank you, I will try to change the weight and add
0
Reply
Boosted
Print Profile
0.08mm layer, 2 walls, 80% infill
This printed extremely well on my second attempt. The c of g is exactly right. I went with the twin fin option and cut some trim tabs for an elevator and it flies perfectly!
The designer has replied
1
Reply
Thank you for the comment. I have a similar design for the mini airplane 2.0 model, where I added a one-piece model
0
Reply
Print Profile
0.08mm layer, 2 walls, 80% infill
Nice!
1
Reply
Print Profile
0.08mm layer, 2 walls, 80% infill
Flyes ok printed really fast
1
Reply
If you're smarter than the PLA, it flies great. just kidding make sure that you bend everything correctly and when you throw the plane think of a straight line. Don't throw it and curve your arm down. if you throw it correctly, it will go a long ways.
1
Reply
Print Profile
0.08mm layer, 2 walls, 80% infill
my model doesn't fly very well. it spins like a tornado during the flight
The designer has replied
0
Reply
Are the front and rear wings bent in the place where the "groove" is? The model must be adjusted manually, as can be seen in the opening photo
0
Reply