F-22 Raptor - String art display - Up

F-22 Raptor - String art display - Up

Boost
103
213
22

Print Profile(1)

All
X1 Carbon
P1S
P1P
X1
X1E
A1

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
5.4 h
1 plate
4.1(17)

Open in Bambu Studio
Boost
103
213
22
16
281
125
Released

Description

Experience the thrill of aviation with this model of the iconic F-22 Raptor.

Designed with precision, this model captures the sleek lines and dynamic stance of the renowned stealth fighter jet.

The model features a string art display that artfully simulates the aircraft in mid-flight, giving the illusion of the F-22 soaring through the skies.

 

The F-22 Raptor model is presented in a suspended display, creating an ethereal, floating effect. This design element not only enhances the visual appeal but also showcases the advanced engineering of the aircraft. The strings are adding to the sense of motion, aerodynamic and realism.

 

  • String art display for a dynamic, floating effect
  • Ideal for aviation enthusiasts and collectors

Check the collection :

F-22 Raptor - String art display - Aiming

F-22 Raptor - String art display - Face

F-22 Raptor - String art display - Side

 

Would greatly appreciate your feedback 😃

 

The F22 by NenZilla can be found at https://www.thingiverse.com/thing:3085856

Comment & Rating (22)

Please fill in your opinion
(0/5000)

Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
neat model. it was a little hairy getting the supports off but slow and steady and I got them off. if I print again I'll try using petg for the support interface
The designer has replied
1
Reply
@jonoitz thank you for your picture and comment :) PETG interface is a good idea i will try to experiment with it, Thanks !
0
Reply
i like
The designer has replied
1
Reply
Thanks 😀
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Support removal broke the model
The designer has replied
0
Reply
@CORBINO to remove the support it s easier if you place the model on the edge of a table remove one third of the support while half of the model is still on the table then turn 180 degree for the other side and finish by the middle with a plier holding stronly to the model, sorry for your broken model
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
support was spotty on tail section causing deformity in model. a couple strings failed before print completion, but still looks cool.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Difficult-to-remove supports
Show original
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
nice
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
Cool Print
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
stopped printing
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
very good cam out great
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Thanks for your rating 👍
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.