AMS lite anti-humidity solution-part1 by HenryFang (亨利方)

HenryFang (亨利方)

3D Printer>3D Printer Accessories

Print Profile(1)

All

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 3 walls, 5% infill

Designer

69 h

10 plates

5.0(14)

Open in Bambu Studio

Boost

821

1384

227

244

1.2 k

104

Released

Description

DrySphere 4D offers advanced moisture control with innovative design for your filament. Featuring silicone rubber seals and four independent enclosure drawers, it ensures each filament stays dry and ready for flawless 3D printing.

it is just 1of 2 part of wholes sytem. another one is for holding filament feeder, and you can find the model at my home page.

see below introduction video on bilibili website.

This model is filaments container. As the video shown, the filament spools are put in four drawers, and they it slide left and right side. so you should have enough space for the drawers opening.

Bill of Material:

Gray PETG — 2800g
Green PETG — 20g
Yellow PETG — 20g
GB846 ST2.2-6.5 — 48PCS 自攻螺钉不锈钢十字槽沉头型(盒装销售) GB846_东明TONG自攻丝螺丝・点触螺丝-米思米官网 (misumi.com.cn)
GB846 ST2.2-9.5 — 16PCS 自攻螺钉不锈钢十字槽沉头型(盒装销售) GB846_东明TONG自攻丝螺丝・点触螺丝-米思米官网 (misumi.com.cn)
4mm Diameter Foaming sealing rope — 5meters 硅胶发泡条发泡圆条...-淘宝网 (taobao.com)
434mm*439mm*10mm thickness Acrylic plate — 1PCS
PTFE tube ( inner diameter >2.5mm, outer diameter 4mm) 4meters

dry box

filament

filament preservation system

Comment & Rating (227)

@cavecchia.andre

Boosted

Fantastic! Finalmente qualcosa di funzionante per AMS lite

@user_2472720276

Funktioniert es im liegendem Zustand genauso wie im stehenden? SIED super aus und ist platzsparend. Funziona allo stesso modo sia da sdraiati che da in piedi? Ha un aspetto fantastico e fa risparmiare spazio.

@cavecchia.andre

Boosted

Replying to @user_2472720276 :

solo coricato, no in piedi

@user_2472720276

Replying to @cavecchia.andre :

Ich habe mich falsch ausgedrückt. Ich wollte wissen ob es Im Liegen nicht hakt ? Also ob es flüssig läuft. Mi sono espresso male. Volevo sapere se non si blocca quando è sdraiato. In altre parole, se scorre senza problemi.

@caa1211

Boosted

完成了，真不錯，感謝精妙的設計

(Edited)

The designer has replied

@HenryFang

好漂亮

@caa1211

Boosted

Replying to @HenryFang :

第三位置可能較遠，我常遇到卡線錯誤，簡單改了一個取代軸來降低阻力，目前用下來沒再遇到問題 https://makerworld.com/zh/models/510795

(Edited)

@ayib

Boosted

OMG, I use A1 to print it. it really kills me. Can Bambu sell it? still have four parts to print.

The designer has replied

@HenryFang

No，seems like you still have 9parts for box and 3parts for feeder. 😅 Don't give up, Bro!

@user_2472720276

Funktioniert es im liegendem Zustand genauso wie im stehenden? Sied super aus und ist platzsparend.

@user_2097678733

Boosted

Almost there. I’m waiting for my colored petg to arrive as well as the screws and Acrylic top. if there is an installation video, please let me know how to find it. I would love to see how the PTFE cable connects to the AMS Lite motor. also, if you guys can post a video of you loading spools, that would be awesome too. Can’t wait😇😅

The designer has replied

@HenryFang

sorry about that. I didn't make an installation instruction. You can check video in my bilibili home page. But it is in Chinese. Please don't do anything to your RFID coil. It doesn't work becasue the cable are too long to read.

@Tuan

Your puppy seems very interested too

@Tuan

For the main part, please spell out the four holes on the side and then spell out the other two, and align the notches of the four bottom circles in the same direction. If you meet all of the above conditions, your installation is accurate. After this, please tighten the screws

@user_2097678733

Boosted

ok my American Friends, help! anyone have the dimensions of the screws so I can buy from Amazon, TEMU, Lowe’s, or Home Depot. this GB846 I can’t make head or tails of dimensions. is an m3 and what’s the length? on the sealant foam tape, 4mm width or is it thickness? if you have links, pls post it.

@Jordayne02

Any luck I can't fine the glass either

@user_2097678733

Boosted

I found a way to do it. Lowe’s has a thicker .22” acrylic 20” x 30” piece. You buy that then and ask them to cut it to 17 & 1/32” x 17 & 1/4” {my dimensions, don’t take my word it. measure your own build}.

@user_2097678733

Boosted

Replying to @Jordayne02 :

all done. That said I’m having second thoughts on if this is a viable option and really worth it if you’re just printing PLA do you really need to do? PETG, I think is worth it. I’m still going through the process of getting used to loading and unloading filaments with this. There hasn’t been a lot of videos from the creator that shows this.

@foxzip1280

太酷啦，目前唯一做到空间节约的AMSLITE封箱方案 That's so cool, The only space-saving AMS lite anti-humidity boxing solution currently available.

@innovi3d

需要加长特氟龙管吗？会不会卡料？

@foxzip1280

Replying to @innovi3d :

要4根特氟龙管，还不短，我总共买了5米，有一根差一点，预估要5.5米；卡料其实还好，因为AMS的齿轮会送料；但是要注意有的料盘，比如纸质的横着放会转不动卡住

@Edelfrosti

Boosted

Print Profile

0.2mm layer, 3 walls, 5% infill

ingenious design, works well, thank you!

@user_1628617735

does the RFID work as well?

@Edelfrosti

Boosted

Replying to @user_1628617735 :

there ia a way to use the rfid, if you unplug it from the original ams lite body and install it into the part underneath the spools, but it needs soldering.