Multiple Sized Trays for Build Plate Cleaner
Copyright Claim
Multiple Sized Trays for Build Plate Cleaner
Boost
62
158
27
Print Profile(1)
All 8 designs in this file
Designer
22.3 h
8 plates
Open in Bambu Studio
Boost
62
158
27
8
128
82
Released
Description
This is a set of different shaped trays for the fantastic Build Plate Cleaner by K-Studio.ca
There are 8 versions in this file:
- 2 Pads 1 Bottle
- 3 Pads
- 2 Pads
- 3 Pads 3 Bottles
- 2 Pads 2 Bottles
- 1 Pad 1 Bottle
- 1 Pad 1 Bottle + Half Tray
- 1 Pad 1 Bottle + Full Tray
The bottle spot is 66mm wide, and perfect for alcohol bottles like the one shown in the photos.
Comment & Rating (27)
All
Boosted
Print Profile
All 8 designs in this file
Nice design and printed great. It will work great in my setup. I really liked the amount of options you gave. I ended up going with a balanced mix
The designer has replied
1
Reply
X1C - Bambu PLA Metal
Love the design. Same error happened on two prints. Maybe not enough infill on stock profile? Not enough adhesion between layers and it can’t make the bridges. Bed adhesion is great. It is pretty warm in the room but the door on the printer is open.
Didn’t happen on any other prints I did today with the same filament.
Any advice?
The designer has replied
0
Reply
oh darn! so sorry it failed on you. Hmmm I'm thinking since it looks like this is all happening at the same layer as where the ironing is for the flat areas, that the ironing settings are the culprit. The profile is set up with a slight modification (ironing flow 25, the default is 10) but is specifically set up using Bambu PLA Matte filaments which might be why this may be happening. I'd recommend turning off ironing if it's not working well with non-matte filaments - as a maybe. But if you get good results normally, maybe this profile has too many customizations - perhaps try:
Try thedefault 0.2mm standard (or turn off everything orange in settings)
OR
If you haven't already, try running both the 'Flow Dynamics' and 'Flow Rate' calibrations for this filament.
Good luck and so sorry this happened!
0
Reply
Replying to @AeonJoey
No worries, we got it sorted. The PLA Metal adhesion maybe a bit different. I have been using the standard PLA profiles for it and its been doing pretty good. Only thing I am noticing is around some parts with through holes, the concentricity is a bit wonky.
Thank you so much for the thoughtful design! Also just saw your printer setup on reddit and its giving me inspiration haha.
0
Reply
Boosted
Thanks for the cool Print
The designer has replied
1
Reply
glad you like it, turned out nice
0
Reply
Boosted
Print Profile
All 8 designs in this file
It just worx! 👍🏼
The designer has replied
1
Reply
Awesome!
0
Reply
Print Profile
All 8 designs in this file
Wonderful print.
1
Reply
Print Profile
All 8 designs in this file
Works great and the listed bottle fits perfectly
1
Reply
Print Profile
All 8 designs in this file
Printed great. I did up the infill to 10% and used Gyroid. I also turned off ironing to save some print time. Great model!
0
Reply
Print Profile
All 8 designs in this file
Other Issues:I had two failures printing with bambu iridium gold. The standard 5% infill was not enough to keep the filament supported when it was printing.
I resliced and upped the infill to 15-20% gyroid and it was flawless. Really fits the suggested alchohol bottle perfectly.
The designer has replied
1
Reply
Oh good to know! I wonder if silk has different adhesion properties
0
Reply
Very nice! :)
The designer has replied
1
Reply
Thank you so much! I love your cleaner I use it every day!
0
Reply
I am going to print one of these as soon as the long print I am doing is over. What filament dryer is that? , it looks very cool.
The designer has replied
1
Reply
oh it’s the Creality space pi, I like that it has the temp presets for different filament types so you don’t have to memorize them.
0
Reply
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld