A1 Mini AMS Lite PTFE Bowden Tube Clip by jayburd

jayburd

3D Printer>3D Printer Accessories

Print Profile(5)

All

A1 mini

P1S

P1P

X1 Carbon

X1E

Loose Fit, 3 Pack, 0.2mm layer, 4 walls, 30% infill

Designer

23 min

1 plate

4.9(103)

Loose Fit, 0.2mm layer, 4 walls, 30% infill

Designer

14 min

1 plate

4.9(18)

Tight Fit, 0.2mm layer, 3 walls, 15% infill

Designer

13 min

1 plate

5.0(10)

Tight Fit, 3 Pack, 0.2mm layer, 3 walls, 15% infill

Designer

19 min

1 plate

4.3(23)

Click to see more

Boost

145

315

160

792

587

Released

Description

A replacement or add on clip for the A1 mini. Install them just like the factory ones. Print profiles include a single version as well as a 3 pack version. If you need more than 3, clone the clip and auto arrange before printing.

Two versions are listed under profile with both single and 3 pack version:

Loose Fit: same as the factory clip, PTFE tube can slide freely in the clip. The wire is a tight fit.
Tight Fit: PTFE slots are sized to hold PTFE tube in place without sliding. Wire slot is the same tight fit and there is a triangle pointing to it. The slots without triangle are for PTFE tube.

Can be printed in any material of your choice.

Single pack takes only 1.5g filament and 8 minutes to print on an A1.

See my A1 Accessories Collection and A1 Purge Basket Collection.

ptfe

clip

Comment & Rating (160)

@th.marci

Print Profile

Loose Fit, 3 Pack, 0.2mm layer, 4 walls, 30% infill

Great print, the PTFE tubes are a bit harder to insert. After that, it slides a lot when not using the data cable. But it's great using with other clips

The designer has replied

@jayburd

Thanks for the feedback. I will be uploading a tight fit version shortly. Testing it now.

@jayburd

Tight fit version uploaded if you would like to give them a try. No more sliding.

@altair3d

Print Profile

Loose Fit, 3 Pack, 0.2mm layer, 4 walls, 30% infill

they works great!

The designer has replied

@jayburd

Awesome

@user_1435532093

Boosted

Print Profile

Tight Fit, 3 Pack, 0.2mm layer, 3 walls, 15% infill

Super passgenau! Die Ptfe Schläuche des AMS und das Kabel vom Extruder passen perfekt hinein. Der A1 schaut direkt viel ordentlicher und aufgeräumter aus:)

@BennyBoots

Print Profile

Tight Fit, 0.2mm layer, 3 walls, 15% infill

these work great. i printed both the right and loose versions and they each have their place. thank you

@BennyBoots

Print Profile

Loose Fit, 0.2mm layer, 4 walls, 30% infill

i use these on my A1 and A1 mini PTFE to the AMS lite. works great. thank you.

@bodenseefisch

Print Profile

Tight Fit, 3 Pack, 0.2mm layer, 3 walls, 15% infill

A little bit too tight even printed 1% smaller

@MKSingularities

Print Profile

Loose Fit, 3 Pack, 0.2mm layer, 4 walls, 30% infill

Great little design, allows for much tidyer PTFE tubes

@aahafen

Print Profile

Loose Fit, 3 Pack, 0.2mm layer, 4 walls, 30% infill

worked like a charm. printed great.

@kstudioca

Print Profile

Loose Fit, 3 Pack, 0.2mm layer, 4 walls, 30% infill

exact match as original clip

@Avaris

Print Profile

Tight Fit, 0.2mm layer, 3 walls, 15% infill

Prints fine and the clearance is exactly as it should be. Holds the PTFE tubes snugly without slipping. Note that the tool head cable on the A1 requires the one with larger fit