Pop Can Dispenser

Pop Can Dispenser

Boost
969
2195
271

Print Profile(3)

All
P1P
P1S
X1
X1 Carbon
X1E
A1

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
13.6 h
2 plates
4.7(184)

Fast Print 0.28mm layer, 2 walls, 7% infill
Fast Print 0.28mm layer, 2 walls, 7% infill
9 h
2 plates
4.8(34)

0.28mm layer, 2 walls, 7% infill
0.28mm layer, 2 walls, 7% infill
11.6 h
2 plates
5.0(1)

Open in Bambu Studio
Boost
969
2195
271
128
3.4 k
2.2 k
Released

Description

Pop/Soda Can dispenser for use inside or outside your fridge. Holds 11 standard US sized cans and automatically pushes the next can to the front. Willing to make adjustments for other sized cans, just comment what you want and I'll make it happen.

 

Dimensions:

420mm x 130mm x 162mm (LWH)
16.5in x 5.12in x 6.38in (LWH)

Comment & Rating (271)

Please fill in your opinion
(0/5000)

I completed the print, don't know if anyone else has the same issue I did, but I recommend printing it a percent or two wider. It printed great, and looks pretty good, the only issue I have is that the cans if they don't go perfectly straight down the ramp they get caught on the sides. Other than that, it printed great.
5
Reply
Any chance that you could make one that is 34cm max. in depth?
The designer has replied
0
Reply
Hi, thanks for the suggestion. I have already uploaded a shorter version that should fit within your size constraints. See link: https://makerworld.com/en/models/46877#profileId-48666
1
Reply
Replying to @dangles_ :
Hello. I see you've deleted the small (less cans) option. I printed it when it was published and the cans do not fall to the lower level in the back, nor can they be removed from the front. They can be loaded though. The can cylinder dimension is too narrow for both openings. Is this why you removed the file? Will you be correcting and re-uploading with the correct dimensions? I like the smaller size for the fridge. Thanks much for your efforts.
0
Reply
Replying to @mfdisme :
Yeah thats exactly why I removed it and I apologize for that. I'll be fixing the model and re-uploading it over the next couple days.
1
Reply
is it possible for these type of cans to adjust the file? they are longer in length and smaller in width. thanks in advance
1
Reply
yes. there is an eu version on here
0
Reply
Made a 16 oz version. Works well.
1
Reply
anyone have the same issue mine can’t fit in a can
1
Reply
Print Profile
Fast Print 0.28mm layer, 2 walls, 7% infill
Was a bit long so I tried to cut out a middle section. Didn't realize it had sloping floors. Oh well. Still works great. Ran out of black so also unintentionally coke zero themed
1
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
first plate printed fine 2nd plate did something I’ve never seen before back part snapped off and before I realized it resulted in suspended air printing
Bed Adhesion Issue:see photo
Strength Issue:see photo
0
Reply
happened twice I’m done with this print
0
Reply
Boosted
Print Profile
0.2mm layer, 2 walls, 15% infill
very nice model, very sturdy
1
Reply
Print Profile
Fast Print 0.28mm layer, 2 walls, 7% infill
Nice print and the cans fit like they should
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
The design is excellent, however, one of the upper prongs broke when fitting it to the other piece, but I was able to repair it with glue
Show original
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Remixes (2)
(Created before license restrict)