NOTICE: REMIX ARE NOT ALLOWED

NOTICE: DO NOT POST ANY OF YOUR PROFILE

_____________________________________________________________________________________________

I design a dash-cam case specific for ESP32-CAM OV2640. You find this on Aliexpress.

The cam of this ESP32 is the standard that you receive with the ESP32 kit.

To close the case you only need x4 M3 screws.

The specific ESP32-CAM OV2640 model is this:

NOTICE: THE TTL DOWNLOADER HAS THE USB TYPE-C. SO THIS CASE IS SPECIFIC FOR THIS ESP32-CAM OV2640 AND FOR THIS TTL DOWNLOADER.

I choose this TTL with USB-C so you will never again broke the side buttons. To be clear , I post a picture of the older TTL version and I broke up so many times the side buttons:

For this case you need this TTL:

As you see in this last pic , you got the new TTL with USB-C and side bottoms on the top.

________________________________________________________________________

For this case you have 2 options to let it power up:

1) 3.7V battery

2) Powerbank and USB-C cable. This is a better option so the heat pass through the USB-C port hole.

____________________________________________________________________________________

NOTICE:

Depending on the way you want to power the ESP32, you will find two profiles:

1) A profile for those who use the ESP32 with the 3.7V battery, so in the profile there is a 0.4mm thick spacer to be printed together with the case

2) A profile for those who use the ESP32 with the power bank, so in the profile there is a 6.2mm thick spacer to be printed together with the case

____________________________________________________________________________________

NOTICE:

I based the case PROFILE for the ESP32 WITH THE BATTERY considering the size of the battery that can be purchased from Aliexpress online. So since I didn't buy it, I simply took the measurements.

If they are wrong, write me a message and I will resolve this error.

____________________________________________________________________________________

NOTICE:

To print the case you need:

1) ABS or higher TEMPERATURE filaments like PC, PA6-GF / CF or PAHT for the case , spacer and lid

2 ) CLEAR PETG to cover the hole of the LED LIGHT

3) TPU 95A HF for the USB-C CAP. You shouldn't have it, because if you want you use the same filament you print the case

____________________________________________________________________________________

HOW TO ASSEMBLE: 
STEP 1

STEP 2

_______________________________________________________________________________
NOTICE: I don't provide the code for it.

_______________________________________________________________________________
 

𝙽𝙾𝚃𝙸𝙲𝙴:

𝚃𝙷𝙸𝚂 𝙸𝚂 𝙰 𝚂𝙸𝙼𝙿𝙻𝙴 𝙿𝚁𝙸𝙽𝚃. 𝙰𝚂 𝚈𝙾𝚄 𝚂𝙴𝙴 𝙸𝙽 𝚃𝙷𝙴 𝙿𝙸𝙲𝚃𝚄𝚁𝙴𝚂 , 𝙼𝚈 𝙼𝙾𝙳𝙴𝙻 𝚂𝚃𝙸𝙲𝙺 𝚅𝙴𝚁𝚈 𝙶𝙾𝙾𝙳 𝙾𝙽 𝚃𝙷𝙴 𝙱𝙴𝙳. 𝚂𝙾 𝙱𝙴𝙵𝙾𝚁𝙴 𝚈𝙾𝚄 𝙶𝙸𝚅𝙴 𝙱𝙰𝙳 𝚁𝙰𝚃𝙸𝙽𝙶 𝚃𝙾 𝙼𝚈 𝙿𝚁𝙾𝙵𝙸𝙻𝙴𝚂, 𝙱𝙴 𝚂𝚄𝚁𝙴 𝚈𝙾𝚄 𝙷𝙰𝚅𝙴 𝙰 𝙶𝙾𝙾𝙳 𝙱𝙴𝙳 𝙰𝙳𝙷𝙴𝚂𝙸𝙾𝙽 𝙰𝙽𝙳 𝙰𝚂𝙺 𝚃𝙾 𝚈𝙾𝚄𝚁𝚂𝙴𝙻𝙵 , 𝚆𝙷𝚈 𝚈𝙾𝚄 𝙳𝙾𝙽'𝚃 𝙷𝙰𝚅𝙴 𝙰 𝙶𝙾𝙾𝙳 𝙱𝙴𝙳 𝙰𝙳𝙷𝙴𝚂𝙸𝙾𝙽. 𝙸 𝙳𝙾𝙽'𝚃 𝚆𝙰𝙽𝚃 𝚃𝙾 𝚄𝙿𝙻𝙾𝙰𝙳 𝙰 𝙻𝙾𝚃 𝙾𝙵 𝙿𝚁𝙾𝙵𝙸𝙻𝙴𝚂 𝙵𝙾𝚁 𝙴𝙰𝙲𝙷 𝚂𝙸𝙽𝙶𝙻𝙴 𝙿𝚁𝙾𝙱𝙻𝙴𝙼 𝚈𝙾𝚄 𝙷𝙰𝚅𝙴 𝙰𝙽𝙳 𝙵𝙾𝚁 𝙴𝚅𝙴𝚁𝚈 𝚂𝙸𝙽𝙶𝙻𝙴 𝙼𝙾𝙳𝙴𝙻! 𝙴𝚅𝙴𝙽 𝚈𝙾𝚄 𝚆𝙰𝙽𝚃 𝚃𝙾 𝚂𝙷𝙰𝚁𝙴 𝙾𝙽𝙴 , 𝙸𝚃 𝙳𝙾𝙴𝚂𝙽'𝚃 𝙼𝙰𝙺𝙴 𝚂𝙴𝙽𝚂𝙴 𝙵𝙾𝚁 𝚃𝙷𝙴 𝚂𝙸𝙼𝙿𝙻𝙴 𝙼𝙾𝙳𝙴𝙻 𝙸𝚃𝚂𝙴𝙻𝙵!

𝙿𝙻𝙴𝙰𝚂𝙴, 𝙻𝙸𝙺𝙴 𝙸 𝚂𝙰𝙸𝙳 𝚃𝙷𝙴 𝙼𝙾𝙳𝙴𝙻 𝚂𝚃𝙸𝙲𝙺𝚂 𝙾𝙽 𝚃𝙷𝙴 𝙱𝙴𝙳 𝙴𝙰𝚂𝚈! 𝙽𝙾𝚃 𝙰𝙻𝚆𝙰𝚈𝚂 𝚁𝙴𝙳𝚄𝙲𝙸𝙽𝙶 𝚃𝙷𝙴 𝚂𝙿𝙴𝙴𝙳 𝙲𝙰𝙽 𝙷𝙴𝙻𝙿 𝚈𝙾𝚄 𝚃𝙾 𝚂𝚃𝙸𝙲𝙺 𝙴𝚅𝙴𝚁𝚈 𝙼𝙾𝙳𝙴𝙻 𝙾𝙽 𝚃𝙷𝙴 𝙿𝙻𝙰𝚃𝙴! 𝚃𝙷𝙰𝙽𝙺 𝚈𝙾𝚄 𝙵𝙾𝚁 𝚃𝙷𝙴 𝚄𝙽𝙳𝙴𝚁𝚂𝚃𝙰𝙽𝙳𝙸𝙽𝙶!

ᴵᶠ ʸᵒᵘ ʰᵃᵛᵉ ᵖʳᵒᵇˡᵉᵐˢ ᵃᵇᵒᵘᵗ ᵗʰᶦˢ ᵐᵒᵈᵉˡ, ʲᵘˢᵗ ˢᵉⁿᵈ ᵐᵉ ᵃ ᵖʳᶦᵛᵃᵗᵉ ᵐᵉˢˢᵃᵍᵉ ᵃⁿᵈ ᴵ'ˡˡ ʰᵉˡᵖ ʸᵒᵘ.

ᴳᶦᵛᵉ ᵐᵉ ᵃ ˡᶦᵏᵉ ᵃⁿᵈ ᶠᵒˡˡᵒʷ ᵐʸ ᵖᵃᵍᵉ.

ᵀʰᵃⁿᵏ ʸᵒᵘ ᵗᵒ ˢᵘᵖᵖᵒʳᵗ ᵐᵉ ᵃⁿᵈ ʰᵃᵖᵖʸ ᵖʳᶦⁿᵗᶦⁿᵍ.