BambuLab AMS Silica box with shovel by TM

3D Printer>3D Printer Accessories

GIF

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

0.16mm layer, 2 walls, 15% infill

Designer

1.5 h

1 plate

4.9(47)

0.16mm layer, 3 walls, 15% infill

3 h

1 plate

5.0(7)

Shovel Only - 0.2 mm layer

35 min

1 plate

5.0(5)

Open in Bambu Studio

Boost

194

465

342

Released

Description

Another Silica box for the ASM inlcuding a shovel

Great design
Great fit into AMS
Great function (rotating lid)
Lid clicks into box
Lid stays securely on the box while opening
Get out with only one finger
Including shovel for easy fill in silica

Designed to print without support!

Comment & Rating (84)

@DethBringa

Boosted

Print Profile

0.16mm layer, 2 walls, 15% infill

5 star print. - 1/2 a star for weak hinge. + 1 star due to scoop fitting perfectly inside the AMS riser drawer. 5.5 stars total? XD. Looks amazing, works great. However, don't print in silk like I did, the hinge breaks off and leaves a hole for the silica beads to fall out of. Not sure if this can be strengthened, but a little blockage behind the hinge hole would be a good addition to this model.

The designer has replied

@TRMgffffggggvgg

To avoid breaking the hinge you should put 1st hinge into the 1st hole of the box. Then bend the whole lid a littebit to spread 2nd hinge to fit into 2nd hole. Don't try to bend the hinge itself since as you see it brakes. What do you mean with: 'a little blockage behind the hinge hole would be a good addition to this model.'?

(Edited)

@DethBringa

Boosted

Sorry for the late reply, I don't often check back for replies. I found your design even works well with a broken hinge except the silica gel beads roll out of the hole where the little hinge clips in. Without a breakage it isn't an issue, but with 1 hinge missing, the beads roll out. My thought was to either change the hole in the side wall into a little block with a hollow or to move that side wall in so you can thicken the hinge piece. The weakness is caused by my printing with silks instead of standard pla so probably not something many ppl will encounter. It still is a great design.

@liang.Zhang

It works perfectly, thanks to the author.

The designer has replied

@TRMgffffggggvgg

you're welcome 😊

@cleeb1983

Print Profile

0.16mm layer, 2 walls, 15% infill

At first I was nervous and was afraid that the hinges would break off when the cover was hung due to insufficient dimensions or insufficient adhesion between the layers. However, it turned out that this was not a problem. Although I already had a small scoop for the beads, I also printed this scoop and am delighted with it. Perfectly dimensioned and aesthetically pleasing.

The designer has replied

@TRMgffffggggvgg

Thanks for your comments!

@JoelVonUndZu

Print Profile

0.16mm layer, 2 walls, 15% infill

Perfect 🤩

The designer has replied

@TRMgffffggggvgg

Thanks for your comment, glad that you're happy with it!

@MicheleMM3D

Print Profile

0.16mm layer, 2 walls, 15% infill

very practical, thank you

(Edited)

The designer has replied

@TRMgffffggggvgg

You're welcome!

(Edited)

@acticom.x1

Boosted

Print Profile

0.16mm layer, 2 walls, 15% infill

Perfect print on X1C using Bambu black Basic PLA. Thanks for the model.

The designer has replied

@TRMgffffggggvgg

You're welcome - thanks for reply!

@double78.tl

Print Profile

0.16mm layer, 2 walls, 15% infill

👍

@an.tatoglou

Print Profile

0.16mm layer, 2 walls, 15% infill

Fits perfectly! nice one!

(Edited)

@user_3634229471

Print Profile

0.16mm layer, 3 walls, 15% infill

i wish the ther was room for the existing clips to fit in the AMS. Otherwise, solid print.

@TRMgffffggggvgg

Hi, I don't know what you mean with: 'i wish the ther was room for the existing clips to fit in the AMS. Otherwise, solid print.' Could you be more precise please?

(Edited)