Broom made of poop lines

Broom made of poop lines

Boost
648
780
160
GIF
GIF

Print Profile(5)

All
A1 mini
P1S
P1P
X1
X1 Carbon
X1E
A1

Broom, elegant version
Broom, elegant version
Designer
2 h
1 plate
4.8(34)

Broom, classic version
Broom, classic version
Designer
1.9 h
1 plate
4.8(22)

All Shapes (choose yours)
All Shapes (choose yours)
Designer
5 h
4 plates
4.8(5)

Broom, sphere version
Broom, sphere version
Designer
1.6 h
1 plate
4.3(4)
Click to see more

Boost
648
780
160
36
573
373
Released

Description

This Broom will allow you to clean all the poop and dirt generated by 3D printing! 🧹 Print is very fast & easy, no support required. You can choose between 3 versions (print profile) of the handle: classic, elegant and sphere.

How does it work ⚙️

This "brush" is made of 4 parts: a handle, an S shape and two threaded parts which has a slightly conical shape, which allows you to apply pressure to the poop lines. This way you will be able to keep the poop lines together. See the animated GIF:

How can I collect poop lines?

Poop lines are generated with each print. Don't throw them away, collect them with these super bins!

 

Poop Line Bin for P1S & X1C

Large Poop Line Bin for P1S & X1C

How to assemble it 🔨

Step 1: fit your first lines (I used about 150) around the "S" part, you can help by holding them in place with a lace or cable tie

Step 2: hold with a hand the 2 threaded parts around the first lines, beyond the S part

Step 3: screw the handle, holding togheter the threated parts

Step 4: cut the excess first lines with scissors and... you're ready!

Warning!

The first step, that of folding and passing the approximately 250 poop lines into the S-shaped piece is the most difficult.

I recommend "tying" the poop lines with a cable or zip tie to keep them tighter. Then you can remove it.

 

For any suggestions, let's talk using the direct message or in the comments!

Updates (April 10, 2024)

I edited the thread part. You can find the oldest version in this print profile.

Comment & Rating (160)

Please fill in your opinion
(0/5000)

Print Profile
Broom, elegant version
still waiting for enough purge lines
The designer has replied
1
Reply
wow did u use the GALAXY PLA?
0
Reply
Replying to @ValeriaMomo :
It is Royal Purple Sparkle Bambu PLA
0
Reply
Print Profile
Broom, elegant version
Qualità di stampa perfetta su P1S ma purtroppo si avvita male e non riesco a avvitarlo tutto.. testato con il pla plus sunlu, riproverò con il bambu basic
The designer has replied
0
Reply
ciao Lorenzo, cavolicchi mi dispiace che ti si avviti male!! posso mandarti in privato un altro modello di parte interna da stampare e mi dici se con quella funziona meglio?
0
Reply
Replying to @ValeriaMomo :
certo grazie mille! come posso contattarti?
0
Reply
Replying to @lorenzofabbri95 :
scrivimi in privato qui su MakerWorld! ti ho già scritto 😃
0
Reply
Print Profile
Broom, classic version
good
The designer has replied
1
Reply
super thx :)
0
Reply
Print Profile
Broom, sphere version
I need to get more poop lines before I can finish it, but it printed nicely and it's a great use of that extra filament. Thank you.
The designer has replied
1
Reply
you are on the right path :D !!
0
Reply
Print Profile
All Shapes (choose yours)
Awesome design!
(Edited)
The designer has replied
1
Reply
thanks you 😊
0
Reply
Print Profile
Broom, classic version
Prints nicely but I don't rhink the brim is needed, especially on the larger parts. It only adds unnecessary work and sharp edges.
The designer has replied
1
Reply
hi, the brim is necessary because 90% of users always have a very dirty plate 🤣 if you are part of the 10% who love to keep the plate clean you can deactivate the brim!
(Edited)
5
Reply
OK so I think it might be my error, but don't print in PETG. I printed this and there is no way it is screwing into the handle. Nowhere near 250lines. I'll try again in PLA to see if it is OK, but my P1S is busy...
The designer has replied
0
Reply
I printed in PLA 😃
(Edited)
0
Reply
Print Profile
MORE STABLE - Gyroid - PETG - 0.2mm layer, 3 walls, 20% inf.
Great project!! I had a lot of trouble screwing and I had to sand (perhaps my settings to blame). I modeled a shovel that attaches to the back because I lack that for cleaning. I have been modeling on Freecad for a short time and I think you will do better than me...
The designer has replied
0
Reply
Thank you for your rating !!!!!
(Edited)
1
Reply
Print Profile
Broom, elegant version
Really nice clean print.
0
Reply
Print Profile
Broom, elegant version
nápad moc dobrý, teď ještě nasbírat ty plugline na štětiny 😁
0
Reply