organiser with grid

Copyright Claim

organiser with grid

Boost
444
838
99

Print Profile(4)

All
X1 Carbon
P1S
P1P
X1
X1E
A1
A1 mini

two plates · 0.2mm layer, 2 walls, 10% infill
two plates · 0.2mm layer, 2 walls, 10% infill
Designer
8.9 h
2 plates
4.8(30)

single plate · 0.2mm layer, 2 walls, 10% infill
single plate · 0.2mm layer, 2 walls, 10% infill
Designer
8.7 h
1 plate
4.8(32)

0.2mm layer, 2 walls, 10% infill - Optimized for the A1 mini
0.2mm layer, 2 walls, 10% infill - Optimized for the A1 mini
6.2 h
2 plates
5.0(12)

0.2mm layer, 2 walls, 10% infill
0.2mm layer, 2 walls, 10% infill
1.9 h
1 plate
4.8(5)

Open in Bambu Studio
Boost
444
838
99
26
1.1 k
482
Released

Description

organiser with grid pattern and removable separator

created in fusion 360

 

photos show printed in black matte pla and brick red petg-cf

  • 0.20mm layer height
  • 10% adaptive cubic infill

dimensions > x: 200mm · y: 100mm · z: 110mm

 

including two print profiles:

  • two plates, for different colours / materials like seen on the photos
  • single plate, for same colour / material

 

note > the separator is a tight fit, with small tolerance, if your printer / filament struggle with smaller tolerances, reduce the scale of the separator in bambu studio by 0.5~1%

 

commercial licence membership available on my patreon

buy me a coffee

 

note: all photos uploaded are of the actual printed model, taken inside a lightbox or in home studio

 

Comment & Rating (99)

Please fill in your opinion
(0/5000)

Print Profile
two plates · 0.2mm layer, 2 walls, 10% infill
(Edited)
Bed Adhesion Issue:Because the sides are chamfered from the bottom AND the top, it leaves the corners to come up over the course of the print which results in over extrusion of the corners. once the print is done, the corners have risen up a quarter to half mil in comparison to the center point of the top of the print. This makes for an uneven structure and the divider doesn’t work as intended as a result.
The designer has replied
0
Reply
sorry to hear about the adhesion issues, however the chamfer does not cause problems for me, i recommend either giving your plate a thorough wash or use 3D LAC (this thing is magic :) )
0
Reply
Replying to @h3li0 :
It’s ok, thanks for your reply :) It’s not so much the bed adhesion, it’s that the corners are up off the bed, thus have nothing to stick to. it’s more the design imo. what’s this you speak of btw, some kind of glue? Sorry I’m rather new to all this. thanks for the help!
0
Reply
indeed it’s adhesion, having the corners at an angle doesn’t mean it warps, from the photos you show it seems like it really did lift the flat side on one of the corners. 3D Lac is an adhesive spray, comes in a can (some people use air spray, but I find this better) it works really great! never have any adhesion issues with it :)
(Edited)
1
Reply
Print Profile
single plate · 0.2mm layer, 2 walls, 10% infill
imprimi em 80% do tamanho original pois era o tamanho que precisava. Tudo perfeito. obrigado
The designer has replied
1
Reply
ficou com um esquema de cor interessante, que filamento e?
0
Reply
marca voolt, 2 cores pinus e tabaco
0
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill
Good profile, fast print.
1
Reply
Print Profile
two plates · 0.2mm layer, 2 walls, 10% infill
I got a perfect print. Great job to the designer 👏
1
Reply
Print Profile
two plates · 0.2mm layer, 2 walls, 10% infill
Very clean model and an easy print.
1
Reply
Print Profile
two plates · 0.2mm layer, 2 walls, 10% infill
Really cool print out of the box. Without any changes it was really good printable. I had a little bit stringing but not so much as with my other printers. I used Charcoal Black Matte and Orange for the print. Really cool design and will take place in our Bathroom as organizer for our Brushes.
(Edited)
The designer has replied
0
Reply
looks great, thanks for sharing
0
Reply
Thx very much for the file, I printed it on my P1S but scaled it to 75%, it was enough for my wife's desk. As you see on the picture I modelized an addon for your design.
(Edited)
The designer has replied
0
Reply
very cool, thanks for sharing
0
Reply
Print Profile
two plates · 0.2mm layer, 2 walls, 10% infill
Printed really well - updated my PETG print profile to slow things down and it worked.
The designer has replied
0
Reply
looking good 👍
0
Reply
Boosted
Print Profile
two plates · 0.2mm layer, 2 walls, 10% infill
add a new profile
1
Reply
Print Profile
0.2mm layer, 2 walls, 10% infill - Optimized for the A1 mini
works perfectly
(Edited)
0
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.