Q-tips dispenser
Copyright Claim
Q-tips dispenser
Boost
42
82
36
Print Profile(3)
Normal - 0.2mm layer, 2 walls, 10% infill
Designer
1.5 h
1 plate
Smaller - 0.2mm layer, 2 walls, 10% infill
Designer
1.3 h
1 plate
Slim - 0.2mm layer, 2 walls, 10% infill
Designer
1.5 h
1 plate
Boost
42
82
36
0
413
222
Released
Description
You have the option to select from three different sizes. The smaller version features a larger opening and a lower profile. The slim version, on the other hand, offers a more compact opening, while the normal version stands taller than the smaller one and provides a larger opening.
EDIT:
I added a top cover for the dispenser. Print with support if your bridges aren't good.
Comment & Rating (36)
All
Print Profile
Normal - 0.2mm layer, 2 walls, 10% infill
my q tips did not dispense well, but that might be down to my brand of q tips (Amazon basics).
will try scaling the print wider to accommodate.
0
Reply
Print Profile
Normal - 0.2mm layer, 2 walls, 10% infill
sieht gut aus, aber die Öffnung ist zu eng
0
Reply
Print Profile
Normal - 0.2mm layer, 2 walls, 10% infill
We did not find any Q-tips that would fit through the opening so we'll use our original print for wooden toothpicks. Printing itself worked very well, looks great. Maybe we'll revisit and print it bigger at some point.
The designer has replied
0
Reply
Thank you for your feedback. Can you please provide me with the dimensions of your Q-tips?
(Edited)1
Reply
Replying to @patrik0504
Sure. We tried a few brands.
Most of those were 8cm in length, which is perfect for the dispenser. The slimmest Q-tips that we found had a diameter around 0,7 cm (on the ends). We were able to push them through the opening one by one, but even those wouldn't get their without force.
Also they blocked themselves very easily, turning pushing them manually into quite the frustrating game :D
The Box found a good place in the dining room tho. Toothpicks for everyone! ^^
Thanks for your answer and sorry that it took me so long to respond.
0
Reply
Print Profile
Normal - 0.2mm layer, 2 walls, 10% infill
I've never successfully had a swab just dispense. They always get stuck on one another. Needs a larger gap in the bottom.
1
Reply
Print Profile
Smaller - 0.2mm layer, 2 walls, 10% infill
Really good model. Worked good and all fit like it should.
The designer has replied
0
Reply
Thank you for sharing your feedback. I appreciate your input. If there's anything else you'd like to add, please don't hesitate to let me know.
0
Reply
Print Profile
Slim - 0.2mm layer, 2 walls, 10% infill
Printed well, but the opening is not wide enough to let qtips to fall down
0
Reply
Print Profile
Normal - 0.2mm layer, 2 walls, 10% infill
modified it in slicer because its to narrow for the qtips
0
Reply
I like the design put needs a lid a bigger gap. They always get stuck. Needs a way to keep the dust off. from the picture I thought it had a lid.
0
Reply
sehr schön, aber die Öffnung ist zu klein. deher kommen keine Q-Tips nach...
0
Reply
Print Profile
Normal - 0.2mm layer, 2 walls, 10% infill
Der Auswurfschacht ist etwas zu niedrig. Etwas größerer Spalt und es wäre perfekt 😁
0
Reply
License
This work is licensed under a
Creative Commons Attribution-NoncommercialRelated Models
© 2024 MakerWorld