Bambu Lab Extra-Over-Engineered Y-Splitter
Remixed by
Copyright Claim
Bambu Lab Extra-Over-Engineered Y-Splitter
Remixed by
Boost
22
79
29
Print Profile(3)
0.12mm layer, 2 walls, 15% infill
Designer
1.2 h
1 plate
0.2mm layer, 2 walls, 15% infill
Designer
46 min
1 plate
0.12mm layer, 2 walls, 15% infill
47 min
1 plate
Boost
22
79
29
1
315
156
Released
Description
Based on the Bambu Lab Over-Engineered Y-Splitter version 2, I modified the filament entry side for a smooth filament entry and do not catch up due to the gap between the PTFE tube and the entry.
In the picture, on left is the original and right is the mod.
You will need to download the locking clip here
https://www.printables.com/model/298958-bambu-lab-over-engineered-y-splitter
Use release rings: QTY: 3 of PC4-UM2 from Amazon.
Comment & Rating (29)
All
Print Profile
0.12mm layer, 2 walls, 15% infill
Great 3d.
0
Reply
Print Profile
0.12mm layer, 2 walls, 15% infill
0
Reply
Print Profile
0.12mm layer, 2 walls, 15% infill
Die Clips neigen zum brechen
The designer has replied
0
Reply
vielen Dank für Ihre Bewertung trotz des Problems, das Sie hatten. Die ursprüngliche Y-Splitter Designer empfehlen, diese Trennringe zu verwenden: QTY: 3 von PC4-UM2 von amazon.
0
Reply
Replying to @G__W__
They are not available on Amazon Germany or elsewhere. When googling PC4-UM2 I only find search results relevant to the US.
edit: I believe I found them on eBay: https://www.ebay.de/itm/387024710601
(Edited)0
Reply
Replying to @user_3615294522
Used to be on Amazon.de. But you can still get them from Aliexpress.
0
Reply
Print Profile
0.2mm layer, 2 walls, 15% infill
It didn't help me. I just had to put the AMS to the side to reduce the amount of tube and friction.
The designer has replied
0
Reply
I'm sorry to hear that. What is the issue you're facing? Perhaps I can offer some assistance. What I did was modify the Y-splitter for smooth filament entry. The original Y-splitter designer recommends using these release rings: QTY: 3 of PC4-UM2 from Amazon.
0
Reply
Would you like to follow up whats wrong?
0
Reply
Print Profile
0.12mm layer, 2 walls, 15% infill
Works great so far
The designer has replied
0
Reply
thank you!
0
Reply
There wasn't enough of a lock on mine and the tube just slides right out.
The designer has replied
0
Reply
Try using these release rings: 3 of PC4-UM2 from Amazon. The printed ones are weaker.
0
Reply
Print Profile
0.12mm layer, 2 walls, 15% infill
the push in pieces are kind of fragile but other than that works great
(Edited)The designer has replied
0
Reply
Thank you for the feedback. The release ring is rather fragile, I agree, but that is not my design, what I did was mod the Y-splitter for smooth filament entry. The original Y-splitter designer recommend to use these release rings: QTY: 3 of PC4-UM2 from amazon.
0
Reply
Print Profile
0.12mm layer, 2 walls, 15% infill
The hole for the filament is too small
0
Reply
Print Profile
0.12mm layer, 2 walls, 15% infill
Thank you. Already used to print from dryer.
0
Reply
Print Profile
0.12mm layer, 2 walls, 15% infill
(Edited)
Other Issues:tube slipping out
The designer has replied
1
Reply
Try using these release rings: 3 of PC4-UM2 from Amazon. The printed ones are weaker.
0
Reply
This remix is based on
License
This work is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike
© 2024 MakerWorld