X1 X1C Chamber Screw Hole Cover
Copyright Claim
X1 X1C Chamber Screw Hole Cover
Boost
26
64
23
Print Profile(4)
45 Degree Chamfer Version 0.2mm layer, 2 walls, 15% infill
Designer
29 min
1 plate
0.2mm layer, 2 walls, 15% infill, gyroid infill, no supports
Designer
29 min
1 plate
No Chamfer & Lay Flash With Adjusted Spacing And Height
50 min
1 plate
0.12mm layer, 2 walls, 15% infill
24 min
1 plate
Boost
26
64
23
0
121
56
Released
Description
This is a cover for the screw holes found in the Bambu X1C rear chamber shelf. This cover keeps filament and other debris from collecting in these holes. "Ounce of prevention…"
NOTE: Installation is designed to be tight, hence the use of TPU. Install from the left to the right, lining up the inserts and then push firmly across the top.
Comment & Rating (23)
All
Works but won't sit entirely flush for me
The designer has replied
1
Reply
Thank you for the feedback! This is designed for a tight fit. I didn't want it coming loose since it is in the print chamber. Pressing firmly should help along with some time in the chamber. Make sure to check out my other Bambu Printer Accessories. More to come so follow to get updates. Thanks again!
0
Reply
The filet on the top is very unfriendly to print
The designer has replied
0
Reply
@NaNraY I could redesign one for you without the fillet. Let me know if you'd like me to do that. However, I had no issues printing this using TPU95. What issues did you have?
0
Reply
Replying to @YelTrikDesigns
Hi, thanks for responding!
The overhang is gradual and low angle which causes a messy underside, if it was more steep it would have more support from previous layers.
0
Reply
Replying to @NaNraY
@NaNraY, Interesting suggestion and one I may give a try. I just looked at mine and there's no "message underside", but I realize with TPU95 it can be difficult to print if settings and filament are not dialed in. If you'd like me to make you a new version, just let me know what angle you'd like and I'll post it.
0
Reply
Print Profile
45 Degree Chamfer Version 0.2mm layer, 2 walls, 15% infill
good fit
The designer has replied
1
Reply
Thank you for the 5 star rating! Make sure you check out my other Bambu Printer Accessories. More on the way, so LIKE and FOLLOW for updates.
0
Reply
Print Profile
45 Degree Chamfer Version 0.2mm layer, 2 walls, 15% infill
i like the design and printed just in pla. but the fit is so tight, id wouldn't fit.
i snapped off the left and right walls, then the fit is better (and the top plate covers the holes)
The designer has replied
0
Reply
As mentioned in the Note of the model description and also in the print profile, this is a TPU print, not a PLA print. But, yeah rate it low because you didn't use the correct filament.
(Edited)0
Reply
nice job! i cant wait to print this!
0
Reply
Print Profile
45 Degree Chamfer Version 0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Thank you for the 5 star rating! Make sure you check out my other models and Bambu Printer Accessories. More on the way, so LIKE and FOLLOW for updates.
0
Reply
Print Profile
45 Degree Chamfer Version 0.2mm layer, 2 walls, 15% infill
The designer has replied
1
Reply
Thank you for the 5 star rating! Make sure you check out my other Bambu Printer Accessories. More on the way, so follow me for updates.
0
Reply
Print Profile
45 Degree Chamfer Version 0.2mm layer, 2 walls, 15% infill
1
Reply
Print Profile
No Chamfer & Lay Flash With Adjusted Spacing And Height
0
Reply
Print Profile
No Chamfer & Lay Flash With Adjusted Spacing And Height
0
Reply
License
This work is licensed under a Standard Digital File License.
You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.
Related Models
© 2024 MakerWorld