Gate latch

Many24
Household>Garden
Copyright Claim

Gate latch

Many24
Boost
59
98
23

Print Profile(1)

All
P1S
P1P
X1
X1 Carbon
X1E
A1
1 set, 0.2mm layer, 2 walls, 15% infill
1 set, 0.2mm layer, 2 walls, 15% infill
49 min
1 plate
5.0(22)
Open in Bambu Studio
Boost
59
98
23
5
215
177
Released

Description

This is a very simple garden gate latch, easy to print, easy to install.

To assembly it, you will just need hardware mentioned below.

I recommend using locking glue to secure the bolt and nut over time, and to grease the “bearing”:

Print instructions

  • Print in PETG or any other outdoor suitable material
  • No supports needed
  • Print with 4+ perimeters

Additional hardware needed

  • 1x M4x18 bolt
  • 1x M4 nut
  • 3x screws

Optional

  • Locking glue
  • Grease


door
garden
lock
latch
gate
petlice
closing
doorlock
garden
dvere
branka
zavirat
zavora
vratka

Comment & Rating (23)

Please fill in your opinion
(0/5000)
level
@steffe
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
super detailed, fast print. excellent!
Show original
0
Reply
level
@user_3819349730
Boosted
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
perfect for what I needed
0
Reply
level
@mateuszpm27
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
It turned out nice but... 15% infil is not realy structuraly solid. It bends a bit to much for my liking.
(Edited)
0
Reply
level
@TinyTomRC
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
thank you for the file, it printed perfectly
0
Reply
level
@Tyralion
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
Perfect! Thx!
0
Reply
level
@pez2001
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
just installed it to replace a broken door lock
0
Reply
level
@Collinsdylan1
Boosted
great
0
Reply
level
@jochengerster
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
Works great!
0
Reply
level
@jonas2612
Boosted
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
Works perfectly fine! Used it on the stable for my ducks.
0
Reply
level
@kilowong
Print Profile
1 set, 0.2mm layer, 2 walls, 15% infill
good design a simple and light cost.
0
Reply

License

This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share Alike

Related Models

PVC Pipe connector (20mm) for tinywhoop gates

PVC Pipe connector (20mm) for tinywhoop gates

DaDesasta
4
9
7
Golden Gate Bridge

Golden Gate Bridge

FallenAngel
0
13
16
Alfira Figure (Baldur's Gate 3)

Alfira Figure (Baldur's Gate 3)

WesleyPrints
0
8
8
Padlock Latch

Padlock Latch

NickSiri
0
6
9
PrivacyTermsGuidelinesFAQCookie PolicyCookie SettingsHot Searches
© 2024 MakerWorld