Glider kit card (flies great) by 3dprintdude

3dprintdude

Toys & Games>Other Toys & Games

Print Profile(5)

All

P1P

P1S

X1 Carbon

X1E

A1 mini

0.05mm layer, 1 walls, 5% infill

Designer

1.1 h

1 plate

4.4(33)

0.05mm layer, 2 walls, 5% infill

1.1 h

1 plate

4.3(26)

PLA 0.16mm layer, 3 walls, 13% infill

27 min

1 plate

4.6(7)

0.08mm layer, 2 walls, 5% infill

49 min

1 plate

3.9(17)

Click to see more

Boost

343

635

1.5 k

862

Released

Description

This is a kit card of a glider. It glides very well if weighted properly. I made this because I saw many kit card airplanes that did not fly and wanted to make one. It must be printed with a 0.05 mm layer height. If the glider nose dives then print out the light weight securer. If the airplane flips backward print out the heavy weight securer. (also make sure that the wings are slanted back to provide lift. If they are slanted forward then the fuselage sides need to swap)

Some recommendations for this print are.

Clean your print bed before printing.
Print with around 5% infill.
Do not print to fast. (stay near 200 m/s or less)

Documentation (5)

Assembly Guide (5)

MUIF7308[1]_6a5a362f-7f1c-4911-a7b0-f4ff385a9103.jpg

JZOFE1217[1]_11e2f9fa-3b27-46af-a348-51865466b2cd.jpg

QTJKE4631[1]_6f035622-7799-486c-89aa-30d52597b3e3.jpg

WDDEE6734[1]_dbab0c7e-f974-4172-be76-95862308eb73.jpg

WDDEE6734[1]_c345eef2-3522-4eef-adfe-493cc3bdf876.jpg

Comment & Rating (94)

@jetpad

Print Profile

0.05mm layer, 2 walls, 5% infill

It is the most delicate thing I’ve printed but it came out great and works. You are pushing the limits on what can be printed!

The designer has replied

@user_3673048447

Boosted

credits to the creator! i love it <3

@user_1877107977

Be sure not to spray glue, otherwise you won't be able to take it off at all，一定不要喷胶，要不然根本拿不下来！！！！！

@Stefan3D

Print Profile

0.08mm layer, 2 walls, 5% infill

nice model

@user_1765441182

Print Profile

0.08mm layer, 2 walls, 5% infill

it was a little hard to put together but it flies well and work well once put together.

@SimCo

Print Profile

0.05mm layer, 2 walls, 5% infill

it's amazing that this can be printed and actually fly

(Edited)

@cpt.balu

Print Profile

0.05mm layer, 2 walls, 5% infill

Good profile, the only problem I had was with the balance weight. There was a little layer shift.

(Edited)

@Lazy_Alex

Print Profile

0.05mm layer, 2 walls, 5% infill

Worked great. Kinda'of flies a bit

@Gusher._

Print Profile

0.05mm layer, 2 walls, 5% infill

prints great but is too heavy to actually fly it just nosedives

The designer has replied

@user_3673048447

Boosted

can you get the weight closer to the wings?

@3dprintdude

You may have the two sides of the fuselage reversed, or you could try going into files and printing out the lighter weight nose weight. If it is the fuselage sides are reversed then the back of the wings will be higher up than the front. Also the bottom of the fuselage when they print should be on the outside.

@user_2656605850

Print Profile

0.05mm layer, 2 walls, 5% infill

looks great. good experience for dealing with ultra thin components. one wing split when I carved it off the plate, so it's just decoration but it still looks cool!

The designer has replied

@user_3673048447

Boosted

thanks!

@faerristm

Print Profile

0.05mm layer, 2 walls, 5% infill

doesn’t even flight the slightest

@3dprintdude

If it does not fly and just nose dives then the fuselage sides may be backward and then the wings will be slanted forward. To fix this the sides of the fuselage need to be swapped. If it is something else then I don't no how to help you because all the ones I have made work great.

(Edited)