Universal Car Phone Holder (Fan mount) by Sam.moore.audio

Sam.moore.audio

Tools>Gadgets

Print Profile(8)

All

P1S

P1P

X1 Carbon

X1E

Phone Holder (Small) - 0.2mm layer, 2 walls, 15% infill

Designer

1.4 h

1 plate

4.9(7)

Fan Clip attachment (Small) - 0.2mm layer, 2 walls, 15% infill

Designer

25 min

1 plate

4.5(4)

Phone Holder (Lower sides) - Small

Designer

1.2 h

1 plate

5.0(3)

Fan Clip attachment (Large) - 0.2mm layer, 2 walls, 15% infill

Designer

34 min

1 plate

5.0(2)

Click to see more

Open in Bambu Studio

Boost

122

Released

Description

Universal Car phone holder which clips into your car fan.

Large and Small versions fit wide variety of phone/case combo's. Choose a fan attachment clip suitable for your vehicle, clip them together and off you go.

The small/med/large fan clips are about 15mm, 30mm, and 40mm wide respectively.

The Small phone holder takes phones roughly 10-14mm deep, 70-82mm wide.

The Large phone holder takes phones roughly 13-17mm deep, 80-92mm wide.

I used PLA for these but PETG might be better to allow more bending if required.

The STEP files are attached so anyone is welcome to remix these to suit their phone or vehicle. I can modify bits easily if needed.

Cheers

Comment & Rating (32)

@Sgt_Nexar

very nice design! I have only one issue with my iPhone. when is slide it in it pushes my minus volume button till my phone is completely muted. maybe you could do a redesign with lower left side? anyway great job!

The designer has replied

@Sam.moore.audio

Hi Sgt, Thanks a lot! And sure no problem... How much lower would you need it? Can you let me know the model so I can label the mod too. Cheers!

@Sam.moore.audio

I've just uploaded a mod with ~24mm more clearance :)

@user_177712559

Print Profile

Phone Holder (Large) - 0.2mm layer, 2 walls, 15% infill

it will work

@user_3619420008

Print Profile

Phone Holder (Small) - 0.2mm layer, 2 walls, 15% infill

Que da muy bien hecho, solo me falto usar un filamento resistente a el calor Por que este se deforma por el calor interno del carro

@user_1019387088

This works great in one of my cars. Can you make an attachment clip for vertical fan fin orientation? This would allow me to use it in my other car. Thanks for the great model!

The designer has replied

@Sam.moore.audio

Hi there, That's great to hear! I did think this would be a good idea but hadn't got round to it. I've just uploaded a vertical clip version of the Medium size. Hopefully this works for you. Let me know if not. Ta, Sam

@user_1019387088

Replying to @Sam.moore.audio :

Thank you for making this! It almost fits, but the fan is just a little wider than the clip. Can you extend it slightly by 3-4mm? Also I'm having trouble fitting my pixel 7 phone in the small mount as it is a bit snug and breaks the side tab off. THe large mount size is too big where it wiggles around too freely. If you have a chance, could you make a medium size in between the two?

@El_Revilo

Print Profile

Fan Clip attachment (Small) - 0.2mm layer, 2 walls, 15% infill

only problem I have specifically is that the mount presses my volume button constantly when it's completely seated in the mount. this is still a good and simple design but you should check if this could be a problem for you. A lower version could fix this issue. designing something that diverse to fit is challenging.

The designer has replied

@Sam.moore.audio

Hi there, Thanks for the review and feedback. It wasn't an issue for the phones I tried but a few others have had the same problem. I've just uploaded a mod with ~24mm more clearance :) Please let me know if this works better for you. Sam