A1 mini filament placement box/enclosure
Copyright Claim
A1 mini filament placement box/enclosure
Boost
54
70
8
GIF
GIF
Print Profile(1)
0.28mm layer, 3 walls, 8% infill
Designer
14.1 h
3 plates
Open in Bambu Studio
Boost
54
70
8
0
85
9
Released
Description
A1 Mini riser/spool placement system.
Prepare about 500g of PLA or PET-G. I used natural PLA that I spray painted with grey base color.
For completation you'll need:
- 6006 ball bearing
- 2 PTFE tube couplings (M6 or M10)
- PTFE tube cca 250mm length
- 12 neodymium magnets 4mm diameter 3mm height
- Most importantly: double sided duct tape or good rubber legs to maximize adhesion between the riser box and your table.
Comment & Rating (8)
All
for a1 mini but can’t pr8nt it on a1 mini
5
Reply
Hi! is there any way you could drop links to the products you used to complete the enclosure? If you bought them that is, if you already had them on hand I understand and I’ll scour Amazon. Thank you!
The designer has replied
0
Reply
Sure I'll look it up once I get home, I'm currently using this model of mine to be able to print on a small area and I have no problems with it 😊
0
Reply
https://www.amazon.com/s?k=6006+bearing&;page=3&crid=1LQGRO0KH8OUZ&qid=1719083850&sprefix=6006+bearin%2Cstripbooks-intl-ship%2C241&ref=sr_pg_3
https://www.amazon.com/SIQUK-Fittings-Straight-Pneumatic-Connector/dp/B07L8R4SMG/ref=sr_1_3?crid=2E3ISXKZDVZZY&;dib=eyJ2IjoiMSJ9.iXDZDHg3m8MKMonp_R0YC6nhlIYUu3cEr3rfhcxTQXBNdup1oeo1j5BEnRLQPBVef5CcufiZmmcfkaMB2twrOcNQo-Rn5xEDaBZCSbxR2SlvCmWE_4_BcCXfb0iNkXtgknZ5kTWx08K_cTxBudNmp5Y3xKejYY6F2VVWkKxcmLnD0BtlGNDkTeOC0J7ddkHw0b_jVAiiB3dl9z29JePq6Eq4eJPhsiaJHAiI3tVPhdg.Zk4JZa7Rifp_aTzVDMXtJIwgTqZ0LKN4na_j8UF5ct8&dib_tag=se&keywords=ptfe+coupler&qid=1719083927&sprefix=ptfe+cou%2Caps%2C175&sr=8-3
12 neodymium magnets 4mm diameter 3mm height - havent found that on amazon, i can adjust the model to 4x4mm magnets if you want me to. Dual sided duct tape is the last and most important thing to keep your printer stable on it. Otherwise it will move because the plastic is too smooth ;)
0
Reply
possibile stamparlo con a1 mini?
The designer has replied
0
Reply
Unfortunately not
0
Reply
To vypadá dobře, možná to i utlumí trochu tu tiskárnu a nejsou tak vidět rezonance na výtiscích ?
The designer has replied
0
Reply
To bych neřekl, že má nějaký vliv. Upřímně když jsem na to poprvé tiskárnu posadil a zapl tisk, tak jsem se zhrozil jak na tom jezdila (díky vibracím), ale jakmile se dá ta kobercovka nebo jakákoliv guma/protiskluz dospod, tak se ani nehne. Největší oříšek byl lokalizovat těžiště A1 mini
0
Reply
No more
License
This user content is licensed under a
Creative Commons Attribution-Noncommercial-Share AlikeRelated Models
© 2024 MakerWorld