The Joker - Hueforge - Filament Painting

Copyright Claim

The Joker - Hueforge - Filament Painting

Boost
96
147
20

Print Profile(3)

All
P1S
P1P
X1
X1 Carbon
X1E
A1

2 AMS
2 AMS
Designer
6.9 h
1 plate
5.0(6)

1 AMS
1 AMS
Designer
6.9 h
1 plate
5.0(5)

NO AMS
NO AMS
Designer
6.8 h
1 plate

Boost
96
147
20
6
187
33
Released

Description

This is a Hueforge filament painting of the Dark Knight's psychotic nemesis, The Joker. The frame for all of my, and probably the vast majority of 200x200 prints is HERE.

*

 

This is a simple 5 color print that can easily be done by people with or without AMS units. If you have an A1 mini or any other printer with a bed smaller than the capacity to print 200x200 you can use the slicer to scale the model in the correct profile for your multi color setup just make sure NOT TO SCALE THE Z dimension. I would recommend not scaling smaller than your largest comfortable print area or you will be compressing the same amount of detail into a smaller area and it will probably get muddy, 0.2 Nozzles may mitigate some or all of this problem depending on the model and the size it is scaled down to.

*

 

IMPORTANT: READ BEFORE PRINTING - SUPER IMPORTANT THIS TIME

*

I have uploaded three 3MF profiles. One for people with a single AMS, one for people with two AMS units, and one for people with NO AMS.

*

To print with 1 AMS you need to swap out AMS slot [2] (Color [2]) with Color [5] when the blue gray [Color 2] has completed and fully retracted. The black is used twice in this one so make sure don't swap that out. Once the third color starts printing just load the new spool. Note the AMS will not feed the spool like it does pre print but as long as you have fed 3-4 inches in there and the light goes on it will feed as normal when it swaps back to the last color in AMS slot [2]

*

To print with 2 AMS units all you need to do is load the colors in order and print.

*

To print with NO AMS unit you just need to do manual filaments swaps every color. The 3MF is set to pause at the correct layer heights. At each pause load the next filament color in order by following your unload/load procedure for your particular printer, then hit resume. Repeat until complete. This will be once per color over the entire painting. You have a decent amount of time between swaps, and is actually harder to mess up because it pauses unlike when using the AMS.

*

Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm. There are some recommended speed changes in my 3MF files and a layer height modifier to print the first 0.64 mm @ 0.16 mm layer height to speed up the print as there is no blending on those layers.

*

Like all of my models this is strictly for personal use. The photo attached is the printed model and frame.

*


Filaments Used:
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA BambuLab Basic Blue Gray Transmission Distance: 3.1
PLA BambuLab Matte Ash Gray Transmission Distance: 1.5
PLA BambuLab Matte Ivory White Transmission Distance: 3.5
PLA BambuLab Basic Black Transmission Distance: 0.6
PLA BambuLab Basic Red Transmission Distance: 5

*

Swap Instructions:
Start with Black
At layer #8 (0.72mm) swap to Blue Gray
At layer #15 (1.28mm) swap to Ash Gray
At layer #21 (1.76mm) swap to Ivory White
At layer #29 (2.4mm) swap to Black
At layer #31 (2.56mm) swap to Red for the rest.

Comment & Rating (20)

Please fill in your opinion
(0/5000)

Boosted
Super nice!!! Thanks!! Would be awesome if you could do Harley Quinn same style!!!
The designer has replied
1
Reply
turned out perfect. i'll keep that in mind for future projects
1
Reply
Just uploaded the Harley Quinn companion piece
1
Reply
Boosted
Replying to @BedlamThreadz :
Amazing, just saw this today, will be doing it tomorrow. Many thanks and a big well done!!
1
Reply
Sieht sehr gut aus.
The designer has replied
1
Reply
thank you!
0
Reply
Boosted
Print Profile
1 AMS
Love it, please more in this Artstile ❤️❤️❤️
1
Reply
Print Profile
1 AMS
stampa molto bella
1
Reply
Printed very well.
1
Reply
Print Profile
2 AMS
The designer has replied
1
Reply
those color subs turned out 🔥
(Edited)
1
Reply
Replying to @BedlamThreadz :
YES!! Thanks, was so excited about how it turned out I thought I’d better share a pic! Thanks for the print!!❤️❤️
(Edited)
1
Reply
Print Profile
2 AMS
1
Reply
Print Profile
2 AMS
sehr cool ! Danke dafür.
1
Reply
Print Profile
2 AMS
1
Reply
Print Profile
2 AMS
1
Reply

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.