Bambu Spool - Voronoi Edition Remixed by andythilo

Remixed by

andythilo

3D Printer>3D Printer Accessories

Print Profile(2)

All

P1S

P1P

X1 Carbon

X1E

0.2mm layer, 2 walls, 100% infill

Designer

6.1 h

2 plates

4.9(78)

0.2mm layer, 2 walls, 30% infill

4.5 h

2 plates

4.9(8)

Boost

188

391

561

913

Released

Description

This is my Voronoi edition of the Bambu reusable spool. Retains the filament marker inserts from my Honeycomb spools along with filament retension holes for re-spooling and tab for use with bambu refills. The tab can be easily cut off if needed.

I have also re-sized this slightly adding 1mm to each side. Using a 100% infill (only adds 15g of filament per side), this brings its weight to match the OEM bambu spool as seen in the photos. The spool runs perfectly in the AMS.

Filament markers can be downloaded from my Honeycomb edition spool - https://makerworld.com/en/models/73599#profileId-105962

Comment & Rating (96)

@IconicFAB

I had suspicions of this model that it will be hard to print and it will take ages to do so. Not that hard. Took ages, yes. But at the end - i think this is the coolest re-usable spool I have now.

The designer has replied

@andythilo

Looks great, thanks for the rating!

@MaD3dDesigns

thanks for sharing this model. your spool design works great for refills. I do have an issue with the reapooling. I printed this in PLA+ and I found that the soool swells a bit after respooling and will fit extremely tight in the AMS causing it to error. I’m printing a set in PETG now to see if it works better. what are you guys using to print this. thanks

The designer has replied

@andythilo

Hi, I can’t say I’ve ever noticed it swelling, I use them in my AMS all the time. Did you dry the filament after respooling, wonder if the spool warped?

@Philuk56

Print Profile

0.2mm layer, 2 walls, 100% infill

just what I needed for my cardboard spools!

The designer has replied

@andythilo

Looks brilliant l!

@nkildal

Print Profile

0.2mm layer, 2 walls, 30% infill

Printed with Bambu Lab ABS - 3 spools so far without any issues. Works great in AMS. Prints in a bit under 2,5 hours for each spool side.

@dragoncommando3

Print Profile

0.2mm layer, 2 walls, 100% infill

I love how efficient this print was. I would say that Plate 2 needs a little more support on the connection bit. because that broke off while I was getting the support material off.

The designer has replied

@andythilo

Doesn’t need supports, print eithout

@Hiflier68

I printed a few yesterday in PETG. Excellent file, printed perfectly

@Toopy

Boosted

Print Profile

0.2mm layer, 2 walls, 100% infill

great spool design, BBL refills fit perfectly. works well in AMS. Printed in ABS for heat resistance

@mydarkthawts

Boosted

Print Profile

0.2mm layer, 2 walls, 30% infill

Very well done, designer!!! I made one for each of my filament colors. It does not swell or warp when respooling. I printed the one with 30% gyroid infill as I also did not need the 100% infill to match the original bambu spool weight. It also saves filament and the spools print faster. Printed on the P1S using generic cheap PLA+ filament from amazon that was fed from my AMS issue free.