A1 Heatbed Cable Protector


Print Profile(22)

0.2mm layer, 2 walls, 15% infill
0.2mm layer, 2 walls, 15% infill
Designer
A129 min
4.9
PETG Profile with Gyroid Infill
PETG Profile with Gyroid Infill
A131 min
4.9
Can be taken apart again, 0.2mm, 2 walls, brim
Can be taken apart again, 0.2mm, 2 walls, brim
A126 min
4.9
A1 Mini Printable - STRONG - 0.16mm layer, 4 walls, 100% infill
A1 Mini Printable - STRONG - 0.16mm layer, 4 walls, 100% infill
A1 mini, P1S, P1P, X1, X1 Carbon, X1E, A140 min
4.9
Click to see more

1057
1520
1923
12.1 k
13.5 k
Released
Copyright Claim
Model
Comment & Rating
Remixes
Related Models

Model

This is an Official Heatbed Cable Protector for the Bambu Lab A1 3D printer.

To install, follow these easy steps:

  1. Ensure proper alignment by verifying that the arrows on both halves are directed toward the cable root.
  2. Securely fasten the two halves until a snug and flush connection is achieved.

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Comment & Rating (1923)

0/5000

0.2mm layer, 2 walls, 15% infill

It's fine, fits well. Shame we have to print this though.

9
Reply

Be glad they reacted so fast and addressed it. You cannot expect this to happen with Anycubic or Creality.(Edited)

33
Reply

Yea I am sure that is a difficult task to print a small part with a 3D printer.(Edited)

16
Reply

@DeweyCox Not the point, but thanks(Edited)

3
Reply
0.2mm layer, 2 walls, 15% infill

Printed without issue and fits snuggly!

6
Reply
Model Comment

[STRONG] 0.16mm layer, 4 walls, 100% infill Printed and tested great. Need to use a piler to clamp it together. Cheers (Edited)

3
Reply
0.2mm layer, 2 walls, 15% infill

Nice, fast print .

3
Reply
0.2mm layer, 2 walls, 15% infill

Passt gut. Aber schade das man es überhaupt benötigt. Ich hoffe die Ersatzteile werden bald verschickt. (Edited)

0
Reply

Immerhin wurde sofort reagiert und eine Lösung bereitgestellt. Das einzige was ich nicht herausgefunden habe, ist halt, wie man das Teil wieder raus bekommt. (Edited)

4
Reply

@DoonPedroo Ich habe es schon versucht und leicht wieder abbekommen wenn man mit dem Fingernagel etwas dazwischendrückt(Edited)

1
Reply

Danke werde mal gleich probieren.

0
Reply
0.2mm layer, 2 walls, 15% infill

Easy print. Thanks for a preventative fix.

3
Reply
0.2mm layer, 2 walls, 15% infill

I hope my A1 Will not burn 😁

1
Reply

Saaammmmmeeee

0
Reply
PETG - High Strength

Printed this in my ugliest brown because bambu going from "It's OK, we'll send you a new bed in 2 weeks, continue using it, just print this." to "STOP IMMEDIATELY WE'RE 3 MONTHS OUT BECAUSE WE DON'T KNOW THE ISSUE!!" Is a pretty shitty situation. Prints and fits perfectly by the way.

1
Reply

Yeah, BBL support is pretty bad. I had a bed that did not heat (not related to this problem I don't think) and after almost a month of back and forth they finally said they would replace the print and a shipping label was forth coming. Over a week now and not return label and they blame the delay on this problem, WHAT THE H. How does this problem keep them from providing a label to at least get my defective printer returned. While I still believe their printers are the best in the world the only thing it seems their support is good at is delays and blaming the delay on something other than their poor support.

0
Reply
Can be taken apart again, 0.2mm, 2 walls, brim

Great profile, prints great and the cutout for re-opening is massively appreciated.

1
Reply
Can be taken apart again, 0.2mm, 2 walls, brim

works perfectly and pretty easy to get off.

1
Reply

Remixes (0)

There are no remixes yet