AMS Saver V5 by madizmo

madizmo

3D Printer>3D Printer Parts

Print Profile(8)

All

P1S

P1P

X1 Carbon

X1E

0.16mm layer, 3 walls, 10% infill

Designer

2.6 h

1 plate

4.8(168)

AMS saver with filament guides

Designer

2.4 h

1 plate

4.7(183)

Basic PLA Print - 0.2mm layer, 2 walls, 10% infill

1.5 h

1 plate

4.8(55)

All-In-One/SaverV5+Guide, Arachne, 0.16mm layer, 3 walls, 10% infill

3 h

1 plate

4.7(71)

Click to see more

Boost

1037

2312

687

6 k

4 k

Released

Description

This is the latest version of my AMS saver after bambu asked me to take down my old models. Apparently some people managed to damage the feeder leds with some of the previous models. This version mounts to the top of the feeder unit using double sided sticky tape so there is absolutely no chance of causing any damage to your AMS unit. I used the clear 1mm thick sticky tape off Temu on mine and they are stuck very well. I've been using 100mm ptfe tube with no issues, if you seem to get loading issues try 85mm. The ID of the ptfe hole is 4.2mm but because of the print orientation it can still be tight, i run an allen key through it along the top edge to smooth the layers a bit. You can play with flow rate a bit as well if too tight

works best with my filament guides, the ones in the pictures i'm still testing but the originals work great

Disclaimer: This is a modification to the machine and any issues caused by these mods will not be covered by Bambu.

Comment & Rating (687)

@henrybachhuber

Boosted

where do you find these? just wondering :)

The designer has replied

@madizmo

I’m still testing this version but in the description I have the link to my original ones that work great

@cridlr07

Replying to @madizmo :

think they are reffering to your silica bead containers

@madizmo

Replying to @cridlr07 :

didn’t see the red circle on my phone app 🤣🤣 thanks!

@THENAVARROS13

is this supposed to happen ? first time putting them on I reamed the holes as it was too tight 😂😂 also pushing up the release is a pain how can I make it easier ?😭or do I have it on wrong

The designer has replied

@puppetpallmich

PTFE tubes are way too long, try this file to help cut them to the right length https://makerworld.com/en/models/102568#profileId-109242

@THENAVARROS13

Replying to @puppetpallmich :

i cut them to the right length and its still spinning with the roll :(

@madizmo

Your PTFE is WAY too long, should be 100mm max length. The hole is definitely snug but if you ream it out too much it will make it too loose

@kyle.e.hansen

Print Profile

0.2mm strenght - Generic PETG

thanks for sharing!

The designer has replied

@NV.Desings

no problem! thanks for rating👍

@Dannybetz

@madizmo is the ptfe supposed to go all the way down to the grey filament hole? Is that supposed to help reduce wear on that part too? Conflicting reports of how the PTFE is supposed to be mounted, so I wanted to check with you. Thanks for all your time and effort that you put into these models for us to enjoy.

(Edited)

The designer has replied

@madizmo

I push it right to the hole!

@puppetpallmich

Has anyone noticed their filament grinding away the ends to the PTFE tube. I noticed some white dust particles around the grey intake on the ams and some flakes on the filament. It appears that some filament that has rough textures will grind away at the PTFE tubes quite a lot. I know PTFE is a consumable but is there any recommendation to help limit this? Or any more durable brand of PTFE tube?

The designer has replied

@madizmo

Do you have the tube running right down to the feeder inlet? If you don't this is quite possible to happen. Also try and avoid running any abrasive or rough filaments through the AMS as this it what it will do to the internal PTFE tubes inside the AMS too

@ignacioalfranca

i'm seeing the same issue, ptfe tube end grinded

@atm473

Capricorn tube is thicker walled premium ptfe with a smaller ID but the same OD.

@Zerschmetterlin

Just wanted to push your awesome Model. I am also using your old ones and nothing broke or anything! Thanks for uploading a new version, got asked where I got mine several times and needed to say that you were forced to put it down :( Now I can give them a propper link again :) Also linked your v5 in my filament guide and cleaner which was related to your v4 version!

(Edited)

The designer has replied

@madizmo

thanks, I appreciate it 😁

@WeBe3Dprinting

Print Profile

0.16mm layer, 3 walls, 10% infill

prints perfectly with bambu basic pla green. I used velcro to attach them instead.

The designer has replied

@madizmo

That's a great idea!

@user_3865694975

Print Profile

AMS saver with filament guides

tolles Teil benutze es immer. Ohne hatte ich mehr Probleme mit Verknotungen, Leerlauf etc

The designer has replied

@madizmo

Thanks for the feedback! Mine have been running thousands of hours on 4 machines with no more issues and no wear on the feeder inlets either :)

@markron77

Print Profile

AMS saver with filament guides

This is an amazing design! It includes a fully working hinge mechanism that prints in place with no assembly required. I took it off the plate and It had a working mechanism, which I did not expect. I’m surprised nobody has mentioned this in a review. Thanks for creating this and sharing it. I tried to show the various angles of the hinge in my photos.

@TommyCederlund

Print Profile

Basic PLA Print - 0.2mm layer, 2 walls, 10% infill

Great !

License

This work is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

Related Models

Slim Filament Guide for AMS saver

Golub17

Flying Biplane/Glider v5

EEEEEE

152

385

GIF

AMS Handle v5

The_Trap__

Stone Pillar Geocache v5

brand name brick